Serial port in AIX Post: 302333784

10 More Discussions You Might Find Interesting

1. Linux

Urgent - serial port

Hi All, I am a begineer in Linux, I have 4 ports and 3 are operational port 1,port 2 and port 4 (when I plug in serial device I can see it working) but port 3 seems it is not working. I am sure the hardware is fine. when I give command dmesg | grep tty I get, serial 8250:ttyS0 at...

2. Programming

Serial port programming

I am developing an application in c with Linux OS, where a radio modem working at baud rate 9600 will be attached to PC on serial port. More than four such units will be communicating at one time, so there may be jamming or data corruption. Each module will be transmitting Data packets less than...

3. OS X (Apple)

Serial port parameters

Hello, I am trying to use a rs232 device through a USB serial port on my MacBook pro laptop. I think the device needs the communication parameters to be 9600 n 8 1 my question is does anyone know what the default communication parameters are for mac os x 10.5.7 unix? And if the default...

4. Solaris

Serial port on the T5140

What is the serial port on the T5140 used for.

5. Shell Programming and Scripting

Need help with serial port

Hi, I have a external board connected to my serial port. I need to execute "shutdown -r now" command when system boot up. When system boots up it requires a username ans password. Then I need to run my command. I can use rc script but that is rebooting system before it asks for username and...

6. Solaris

How to enable Serial port on ILOM, when Network Port is enabled in parallel

Hi Everyone, In my environment, I have few T5220. On the iLOM Management Card, I have both Network and Serial port are cabled, I don't have any issues while I try to connect using Network Management port, but when I try to connect the serial port for the same server which is actually connected...

7. Web Development

Setup Serial Port

I need to set a serial port to 9600 7E1. How do I accomplish this? I've tried every combination, with no luck.

8. Solaris

Cabling and adapters to communicate to service processor serial port from Windows PC with USB port.

Hello, I have an unloaded T5140 machine and want to access the ILOM for the first time and subsequently the network port after that., and then load Solaris 10 the final January 2011 build. The first part is what confuses me -the cabling. I am coming from a Windows machine (w/appropriate...

9. AIX

How to change from tty03 to tty00 serial port in AIX 5.x?

Hi, We use AIX 5.x, and we have an application that use the info from a server through a serial port tty00. Some days ago, we bought a new two port serial board, and the server assign this new ports as tty02 and tty03, and leaves tty00 and tty01 as unavailable. We cant modify the program and...

10. AIX

Connect GPS to serial port AIX 5.x

HI, Does anyone installed a GPS from his Serial port to an IBM Server serial port with AIX 5.X I would like the rs232 configuration you used on the GPS, and the ttys configuration from your server. Thanks in advance !!!

LEARN ABOUT NETBSD

scc

SCC(4)							   BSD Kernel Interfaces Manual 						    SCC(4)

NAME

     scc -- Zilog 8530 Serial Communications Controller interface

SYNOPSIS

     scc* at ioasic? offset ?

DESCRIPTION

     The scc driver provides support for the Zilog 8530 Serial Communications Controller (SCC) via the IOASIC found on DECstation 5000 models in
     the /100, /20, and /240 series (supported by NetBSD/pmax).

     Each SCC device has two serial ports.  The DECstation 5000 model 20 provides one SCC device.  Other models provide two, but one port of each
     device is dedicated to mouse and keyboard input, respectively.

     Input and output for each line may set to one of following baud rates: 50, 75, 110, 134.5, 150, 300, 600, 1200, 1800, 2400, 4800, 9600,
     19200, 38400, or 57600.

     Speeds up to 230400 are supported by the chip and the motherboard, but speeds higher than 57600 do not work reliably without an external
     clock signal.

FILES

     /dev/ttya
     /dev/ttyb
     /dev/ttyc
     /dev/ttyd

     The mapping from units to serial-hardware outlets is idiosyncratic.  The even ports are wired serial connectors and the odd-numbered ports
     are reserved for mouse and keyboard.

     On machines with one port like Personal DECstations, the single device is ttya.

     On the 5000/1xx and 5000/2xx, the first serial port (default serial console) is ttyc and the second port is ttya.

SEE ALSO

     intro(4), ioasic(4), ttys(5), MAKEDEV(8)

HISTORY

     The scc driver first appeared in 4.4BSD.

     The scc driver was also used for the IOASIC SCC found in DEC Alpha model 3000 TurboCHANNEL based systems; NetBSD/alpha has since been con-
     verted to use the machine-independent zstty(4).

BUGS

     The IOASIC provides internal DMA channels that can be programmed to transfer up to 4096 bytes of data into, or out, of an SCC without further
     software intervention.  This feature of the IOASIC is not yet supported.

     The mapping from device-special files (major and minor number) to chip and port is arguably backwards.  ULTRIX tries to hide the hardware
     mapping, but NetBSD does not.  Users wanting to use ULTRIX compatible tty names /dev/tty0 and /dev/tty1 for the scc comm-port lines should
     make links or device-special files which match their hardware setup.

BSD
								  April 24, 2003							       BSD