07-05-2009
Did you copy over /etc/nsswitch.conf.dns to /etc/nsswitch.conf ?
Looks like you missed that step.
(Solaris 10+) Copy it, and do 'svcadm refresh network/physical'. If refresh doesn't do it, try restart.
(Solaris 8) Copy it, and unplumb and re-plumb your interfaces.
Last edited by frozentin; 07-05-2009 at 05:21 PM..
Reason: OS version info
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
2. Red Hat
Hello,
I have a small desktop running RedHat 5. Depending where I'm at, it connects to the network by a wireless interface or a wired interface. If I'm in an are where there is no wireless network, the box hangs on boot up. It will not timeout and move on. It just hangs. Is there a timeout... (0 Replies)
Discussion started by: garskoci
0 Replies
3. Solaris
Hi, anyone has had experience in a static setting an IPv6 interface?, I'm trying accordance with the admin guide (ipv6 network configuration tasks), configure one interface in the server, actually i can do ping to my default gateway and access the Internet in IPv6, the specific point is however,... (3 Replies)
Discussion started by: pabloluja
3 Replies
4. Solaris
Hi,
Every time when i boot my system i have to manually issue the following commands.
ifconfig elxl0 plumb 192.168.200.129 netmask 255.255.255.0 up
route add default 192.168.200.1
I need some help so that it should be configured permanently and i wouldn't have to manually issue... (2 Replies)
Discussion started by: malikshahid85
2 Replies
5. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
6. Solaris
Hi, I am new in Solaris 11. I can't even make the NIC work. Here is the issue:
Any help will be greatly appreciated. (6 Replies)
Discussion started by: aixlover
6 Replies
7. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
8. IP Networking
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies
9. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
10. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT LINUX
rpc.bootparamd
rpc.bootparamd(1M) System Administration Commands rpc.bootparamd(1M)
NAME
rpc.bootparamd, bootparamd - boot parameter server
SYNOPSIS
/usr/sbin/rpc.bootparamd [-d]
DESCRIPTION
rpc.bootparamd is a server process that provides information from a bootparams database to diskless clients at boot time. See bootparams(4)
The source for the bootparams database is determined by the nsswitch.conf(4) file (on the machine running the rpc.bootparamd process).
OPTIONS
The following options are supported:
-d Display debugging information.
FILES
/etc/bootparams boot parameter data base
/etc/nsswitch.conf configuration file for the name-service switch
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWbsu |
+-----------------------------+-----------------------------+
SEE ALSO
svcs(1),svcadm(1M), bootparams(4), nsswitch.conf(4), attributes(5), smf(5)
NOTES
A diskless client requires service from at least one rpc.bootparamd process running on a server that is on the same IP subnetwork as the
diskless client.
Some routines that compare hostnames use case-sensitive string comparisons; some do not. If an incoming request fails, verify that the
case of the hostname in the file to be parsed matches the case of the hostname called for, and attempt the request again.
The rpc.bootparamd service is managed by the service management facility, smf(5), under the service identifier:
svc:/network/rpc/bootparams
Administrative actions on this service, such as enabling, disabling, or requesting restart, can be performed using svcadm(1M). The ser-
vice's status can be queried using the svcs(1) command.
SunOS 5.10 1 Aug 2004 rpc.bootparamd(1M)