07-03-2009
I thought the original question is a general one, namely : "When do we really need to add a static route on the server?" - hence the wikipedia article. If in your case you have packet loss between client and server software, you should rather debug at network level with tcpdump or other packet traffic / sniffing instrument. If that's not the case, please describe the situation more clearly.
10 More Discussions You Might Find Interesting
1. IP Networking
Hi,
I have a machine that sits on 10.2 network.
I need to ssh from this to another box that is on both 10.125 & 10.140 VLANs
what should I need to do?
Thanks! (3 Replies)
Discussion started by: chaandana
3 Replies
2. HP-UX
I want to make static route how would I proceed?
I'm using "route add DestinationIP gatewayIP hop to 1
I would like to make this permanent, so when it reboots I don't want to loose it, would I do this in netconf file? If so where?
I did a search got this site, it didn't help much. ... (2 Replies)
Discussion started by: catwomen
2 Replies
3. UNIX for Dummies Questions & Answers
Hi,
Request you to please tell me the command or the process to add the static route in redhat linux.
Thanks in Advance.
Regards
Arun (2 Replies)
Discussion started by: Arun.Kakarla
2 Replies
4. Red Hat
I have a machine with an interface that has two different addresses on CentOS 5
eth0: 10.20.21.77
eth0:1 141.218.1.221
If I issue this command I get the result I'm looking for.
/sbin/route add -net 141.218.1.0 netmask 255.255.255.0 gw 10.20.21.77
ip route show dev eth0
141.218.1.0/24... (1 Reply)
Discussion started by: beaker457
1 Replies
5. AIX
#netstat -nr (shows the following with more static routes)
192.168.18.202 10.129.155.1 UGH 0 29 en0 - -
and i just want to remove the above one
i tried
#smitty rmroute
destination type= net
dest add = 192.168.18.202
default gateway= 10.129.155.1
net... (1 Reply)
Discussion started by: pchangba1
1 Replies
6. AIX
Just want to know if someone has a clue about what could be happening here:
I have an AIX box with four NICs in Ether channel connected to a Cisco Switch.
When I try to ping the default gateway, sometimes it works, but sometimes it doesn't work unless it has a defined static route.
Thanks... (1 Reply)
Discussion started by: witt
1 Replies
7. Solaris
Hi all
i have a simple question here
I'm kind of newbie on solaris development
currently i'm trying to add static route to solaris environment
and i got error, each time i add this static route to it
btw this is my command :
root@xxxxxx # ping 1.2.3.1
1.2.3.1 is alive
echo ... (15 Replies)
Discussion started by: l33tbot_if
15 Replies
8. AIX
Anyone know how to edit a static route in AIX? I find myself deleting and then recreating the route with the new information. Would be nice to know how to edit the route. (3 Replies)
Discussion started by: bbbngowc
3 Replies
9. Red Hat
Hello Guys..
I am facing this weird problem of static route not added after reboot!!
Following is my route-<interface> file..
# cat /etc/sysconfig/network-scripts/route-eth0
ADDRESS0=172.31.0.1
NETMASK0=255.255.255.255
GATEWAY0=192.168.208.1
ADDRESS1=172.31.15.2... (3 Replies)
Discussion started by: parth_buch
3 Replies
10. IP Networking
Hi all,
This may be the basic question of Routing but I am a sort of new to networking so I am asking.
Do I need to put route for my router's LAN port ip to WAN (serial) port ip Or the router itself can communicate between its ports without routes.
lan (172.26.40.5) ... (3 Replies)
Discussion started by: dextergenious
3 Replies
LEARN ABOUT NETBSD
ipresend
IPRESEND(1) General Commands Manual IPRESEND(1)
NAME
ipresend - resend IP packets out to network
SYNOPSIS
ipresend [ -EHPRSTX ] [ -d <device> ] [ -g <gateway> ] [ -m <MTU> ] [ -r <filename> ]
DESCRIPTION
ipresend was designed to allow packets to be resent, once captured, back out onto the network for use in testing. ipresend supports a num-
ber of different file formats as input, including saved snoop/tcpdump binary data.
OPTIONS
-d <interface>
Set the interface name to be the name supplied. This is useful with the -P, -S, -T and -E options, where it is not otherwise possi-
ble to associate a packet with an interface. Normal "text packets" can override this setting.
-g <gateway>
Specify the hostname of the gateway through which to route packets. This is required whenever the destination host isn't directly
attached to the same network as the host from which you're sending.
-m <MTU>
Specify the MTU to be used when sending out packets. This option allows you to set a fake MTU, allowing the simulation of network
interfaces with small MTU's without setting them so.
-r <filename>
Specify the filename from which to take input. Default is stdin.
-E The input file is to be text output from etherfind. The text formats which are currently supported are those which result from the
following etherfind option combinations:
etherfind -n
etherfind -n -t
-H The input file is to be hex digits, representing the binary makeup of the packet. No length correction is made, if an incorrect
length is put in the IP header.
-P The input file specified by -i is a binary file produced using libpcap (i.e., tcpdump version 3). Packets are read from this file
as being input (for rule purposes).
-R When sending packets out, send them out "raw" (the way they came in). The only real significance here is that it will expect the
link layer (i.e. ethernet) headers to be prepended to the IP packet being output.
-S The input file is to be in "snoop" format (see RFC 1761). Packets are read from this file and used as input from any interface.
This is perhaps the most useful input type, currently.
-T The input file is to be text output from tcpdump. The text formats which are currently supported are those which result from the
following tcpdump option combinations:
tcpdump -n
tcpdump -nq
tcpdump -nqt
tcpdump -nqtt
tcpdump -nqte
-X The input file is composed of text descriptions of IP packets.
SEE ALSO
ipftest(1), ipsend(1), iptest(1), bpf(4), ipsend(5), tcpdump(8)
DIAGNOSTICS
Needs to be run as root.
BUGS
Not all of the input formats are sufficiently capable of introducing a wide enough variety of packets for them to be all useful in testing.
If you find any, please send email to me at darrenr@pobox.com
IPRESEND(1)