06-25-2009
Ultra Enterprise 150 is listed under desktops in the Sun ESOL site, right under the Ultra 80... but really, that's irrelevant to troubleshoot the network connection - other than to determine hardware age which may be a factor on HW components mal-functioning.
Here are a couple things you can do to isolate the problem:
- If it is a big self-standing server, it surely has more than 1 NIC. Configure another NIC and try your network connection on the other NIC.
- or better yet, use another server/PC/laptop to test the network connection. Simply configure the server/PC/laptop with the E150's IP.
Obviously, in either case, you'd want to use the very same cable and switch port that are connected to hme0 in the E150.
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Dear Reader,
I have a very unique problem. Quite often my on board ethernet port( hme0 ) related message is appearing in /var/adm/messages.
The message is hme0: babble.. The port is up and alive.
What does this message mean.. Is the on board port is about to fail??
Thanks in advance, (2 Replies)
Discussion started by: joseph_shibu
2 Replies
2. UNIX for Advanced & Expert Users
How do you configure more than one network on a single hme0 interface under SunOS? And why would you want to do this?
Thanx :)
-Michelle (1 Reply)
Discussion started by: Michelle1977
1 Replies
3. BSD
hi
I want to setup my cable modem under OpenBSD. I did not configure my network while installing the system.
When I type, I get
# ifconfig -a
lo0 : ....
...
...
rl0 : ....
...
...
vr0 : ...
...
...
I have two network cards (the machine will be a router).
I created... (1 Reply)
Discussion started by: fnoyan
1 Replies
4. Solaris
Hi all,
Is there any difference between a null modem cable or a modem cable ?
i assume that a null modem cable is a normal cable that i used from cpu serial ports to a modem for dialup.
please correct if i am wrong,
thks (2 Replies)
Discussion started by: waterbear
2 Replies
5. Solaris
Hi .....
My problem is that when i reboot the system i can't connect to the network because my ethernet ( hme0 ) is down , i must up it by ifconfig command
after reboot :
# ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask... (1 Reply)
Discussion started by: tt155
1 Replies
6. Solaris
I have a 420r server it boots up all of the network settings are correct, however the machines network connection is not working. Cant ping anything from it, cant ping it from another machine on the network.
If I ping 127.0.0.1 it says alive.
Is there a chance the network card has been... (2 Replies)
Discussion started by: alanj4
2 Replies
7. Solaris
Hi All,
1. modify /etc/default/login file as
make commented # console=
2.put my laptops ip at both
/etc/inet/ipnodes and /etc/host file
still i can login via telnet/ftp through a DB9-serial cable, but when i tried
through a lan stratight cable directly connected that machine... (7 Replies)
Discussion started by: mahadib
7 Replies
8. Solaris
Hi all,
really interesting thing I have encountered . So :
root@host4 # uname -a
SunOS host4 5.9 Generic_122300-31 sun4u sparc SUNW,Sun-Fire-880
root@host4 # scinstall -p
3.2
latest recommended patches applied ..all SUN cluster patches applied.
SUN cluster software installed without... (2 Replies)
Discussion started by: samar
2 Replies
9. Solaris
We are unable to ping from Sun Ultra 60 to Ultra 10 machine and vice versa. We are getting an error message Cable Link Down ?. It was working fine.
Troubleshooting steps taken.
1) Changed the IPaddresses on both machines 192.168.10.10 and 192.168.10.20. These machines connected through 8 port... (2 Replies)
Discussion started by: vijaykrishna
2 Replies
10. Red Hat
I am facing strange problem regarding hostname on my Linux(2.6.18-164.el5xen x86_64 GNU/Linux), the hostname changes if reboot with lan cable and with NO lan cable
Reboot with lan cable:
The hostname is ubunut
Unable to connect Oracle database using sqlplus some times database is not... (2 Replies)
Discussion started by: LinuxLearner
2 Replies
LEARN ABOUT OPENSOLARIS
scconf_transp_adap_e1000g
scconf_transp_adap_e1000g(1M) System Administration Commands scconf_transp_adap_e1000g(1M)
NAME
scconf_transp_adap_e1000g - configure the Intel PRO/1000 network adapter
DESCRIPTION
Note -
Beginning with the Sun Cluster 3.2 release, Sun Cluster software includes an object-oriented command set. Although Sun Cluster software
still supports the original command set, Sun Cluster procedural documentation uses only the object-oriented command set. For more infor-
mation about the object-oriented command set, see the Intro(1CL) man page.
You can configure e1000g Intel PRO/1000 network adapters as cluster transport adapters. These adapters can only be used with transport type
dlpi.
The e1000g based network adapter connects to a transport switch or to another Ethernet adapter on a different node. In either case, the
connection is made through a transport cable.
When a transport switch is used and the endpoints of the transport cable are configured by using scconf, scinstall, or other tools, you are
asked to specify a port name on the transport switch. You can provide any port name, or accept the default, as long as the name is unique
for the switch.
The default is to set the port name to the node identifier that hosts the adapter at the other end of the cable.
There are no user configurable properties for cluster transport adapters of this type.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Architecture |x86 |
+-----------------------------+-----------------------------+
SEE ALSO
Intro(1CL), clinterconnect(1CL), clnode(1CL), scconf(1M), scinstall(1M), e1000g(7D)
Sun Cluster 3.2 4 May 2006 scconf_transp_adap_e1000g(1M)