SCO 6 + Virtualbox 2 == no NIC Post: 302326767

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Installing nic on sco 5.0.5

How do I install an intel nic on sco 5.0.5 it did not detect when i installed the program:confused:

2. SCO

IRQ conflict between USB and NIC SCO 5.0.7

I have a SCO 5.0.7 server.As there is no parellel port ,printing is done via USB port. After loading the Network Card driver ,during booting the server gets hanged and the NIC driver is not loaded.If the USB ports are disabled the NIC driver gets loaded. As both USB and NIC driver are essential...

3. HP-UX

how can I determine which NIC card is virtual NIC Card

how can I determine which NIC card is virtual NIC Card which condition can make a decision Does HP UX have Virtual Network Adapter Concept if ,it has where I can Find if I Install Virutal Network Adapter or which command that i can get it or which software can generate thanks

4. SCO

Install NIC on SCO openserver 5.0.2

Hi I am trying to install NIC FastNic 10/100 PCI Ethernet driver into PCI# 3 of the GA-SIML Rev 1.0 Motherboard on 1GB Hard-disk driveI have following the instruction on the CD-Disk and when I added NIC by netconfig and I do not know what is the following question: PCI BUS# DEVICE#...

5. Solaris

x86 Solaris 10 nic driver added but not attached. NIC is not detected.

I couldn't install my nic in solaris 10. I compiled and added the driver but failed to attach the driver and ifconfig output shows only loopback dev. Please see the following output and tell me whether my nic has been detected and why the driver failed to attach? My nic is detected in linux...

6. IP Networking

squid proxy: one NIC for inbound & one NIC for outbound?

I am new in squid proxy. My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)? Thank you in advance!

7. Red Hat

I want to tune NIC's rps, rfs and xps value. which NIC device should I modify.

Dear All I want tune my NIC's rps, rfs and xps value. In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1). Here is the question? Which device should I modify ? eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0) Any advice is welcome....

8. SCO

Failure while installing SCO UNIXWare7.1.4 on vmware workstation9, virtualbox

Sir I am trying to install UnixWare7.1.4 on vmware workstation9, virtualbox and I am getting the following error FATAL BOOT ERROR: decompression failed For installing SCO Unixware7.1.4 I have created virtual harddisk of size 18GB, 1024 RAM, 64bit video memory, chosen unixware7.1.4...

9. Linux

Add two different subnet public IPs to single NIC or two different NIC on same box

Hello Admins, My ask is how can I add two different subnet IPs to same box with two different gateways? The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware. How can I get connected...

LEARN ABOUT LINUX

mkfs.bfs

MKFS.BFS(8)						Linux System Administrator's Manual					       MKFS.BFS(8)

NAME

       mkfs.bfs - make an SCO bfs filesystem

SYNOPSIS

       mkfs.bfs [-N nr-of-inodes] [-V volume-name] [-F fsname] device [size-in-blocks]

DESCRIPTION

       mkfs.bfs creates an SCO bfs file-system on a block device (usually a disk partition or a file accessed via the loop device).

       The  size-in-blocks  parameter  is  the	desired size of the file system, in blocks.  If nothing is specified, the entire partition will be
       used.

OPTIONS

       -N     Specify the desired number of inodes (at most 512).  If nothing is specified some default number	in  the  range	48-512	is  picked
	      depending on the size of the partition.

       -V volume-label
	      Specify the volume label. I have no idea if/where this is used.

       -F fsname
	      Specify the fsname. I have no idea if/where this is used.

       -v     Be verbose.

EXIT CODES

       The exit code returned by mkfs.bfs is 0 when all went well, and 1 when something went wrong.

SEE ALSO

       mkfs(8).

AVAILABILITY

       The mkfs.bfs command is part of the util-linux package and is available from ftp://ftp.kernel.org/pub/linux/utils/util-linux/.

Util-linux 2.9x 						   12 Sept 1999 						       MKFS.BFS(8)