06-18-2009
SCO 6 + Virtualbox 2 == no NIC
Has anyone installed SCO 6 in Virtualbox? I was quite successful with 5.0.6 but then when I tried SCO 6, it will not report any nic (I am using resmgr to see who is there). The available cards under virtualbox are pcnet-pci II and II, and a few intel/pro 1000s. I have installed the maintenance pack 4, then I installed the nd package (twice as outlined in
ftp://ftp.sco.com/pub/openserver6/60...rst_nd_install), and rebooted. What next? netadmin does not seem to allow me to add any of the NICs whose drivers I just installed.
Thanks for any help!
Oh, just to let you all know, the driver for the intel card is installed (as /etc/ints/nd/mdi/e1006g).
Last edited by dalek; 06-19-2009 at 12:15 PM..
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
How do I install an intel nic on sco 5.0.5 it did not detect when i installed the program:confused: (2 Replies)
Discussion started by: recono1
2 Replies
2. SCO
I have a SCO 5.0.7 server.As there is no parellel port ,printing is done via USB port.
After loading the Network Card driver ,during booting the server gets hanged and the NIC driver is not loaded.If the USB ports are disabled the NIC driver gets loaded.
As both USB and NIC driver are essential... (0 Replies)
Discussion started by: vikramviky
0 Replies
3. HP-UX
how can I determine which NIC card is virtual NIC Card
which condition can make a decision
Does HP UX have Virtual Network Adapter Concept
if ,it has
where I can Find if I Install Virutal Network Adapter
or which command that i can get it
or which software can generate
thanks (2 Replies)
Discussion started by: alert0919
2 Replies
4. SCO
Hi
I am trying to install NIC FastNic 10/100 PCI Ethernet driver into PCI# 3 of the GA-SIML Rev 1.0 Motherboard on 1GB Hard-disk driveI have following the instruction on the CD-Disk and when I added NIC by netconfig and I do not know what is the following question:
PCI BUS#
DEVICE#... (3 Replies)
Discussion started by: TinhNhi
3 Replies
5. Solaris
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies
6. IP Networking
I am new in squid proxy.
My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)?
Thank you in advance! (4 Replies)
Discussion started by: aixlover
4 Replies
7. Red Hat
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies
8. SCO
Sir I am trying to install UnixWare7.1.4 on vmware workstation9, virtualbox and I am getting the following error
FATAL BOOT ERROR: decompression failed
For installing SCO Unixware7.1.4 I have created virtual harddisk of size 18GB, 1024 RAM, 64bit video memory, chosen unixware7.1.4... (1 Reply)
Discussion started by: rupeshforu3
1 Replies
9. Linux
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
LEARN ABOUT FREEBSD
brandelf
BRANDELF(1) BSD General Commands Manual BRANDELF(1)
NAME
brandelf -- mark an ELF binary for a specific ABI
SYNOPSIS
brandelf [-lv] [-f ELF_ABI_number] [-t string] file ...
DESCRIPTION
The brandelf utility marks an ELF binary to be run under a certain ABI for FreeBSD.
The options are as follows:
-f ELF_ABI_number
Forces branding with the supplied ELF ABI number. Incompatible with the -t option. These values are assigned by SCO/USL.
-l Writes the list of all known ELF types to the standard error.
-v Turns on verbose output.
-t string
Brands the given ELF binaries to be of the string ABI type. Currently supported ABIs are ``FreeBSD'', ``Linux'', and ``SVR4''.
file If -t string is given it will brand file to be of type string, otherwise it will simply display the branding of file.
EXIT STATUS
Exit status is 0 on success, and 1 if the command fails if a file does not exist, is too short, fails to brand properly, or the brand
requested is not one of the known types and the -f option is not set.
EXAMPLES
The following is an example of a typical usage of the brandelf command:
brandelf file
brandelf -t Linux file
SEE ALSO
The Santa Cruz Operation, Inc., System V Application Binary Interface, http://www.sco.com/developer/devspecs/, April 29, 1998 (DRAFT).
HISTORY
The brandelf manual page first appeared in FreeBSD 2.2.
AUTHORS
This manual page was written by John-Mark Gurney <jmg@FreeBSD.org>.
BSD
March 25, 2014 BSD