06-18-2009
Problems Detecting HP Tape Drive
I am trying to install an HP StorageWorks DAT40 Tape drive at SC0 5.0.7. The tape drive is not functional.
When I run #sconf -v this is what I get;
Sdsk ad160 0 0 0 0
Sdsk ad160 0 0 1 0
Stp ad160 0 0 3 0
But when I run #hwconfig -h this is what I get;
device address vec dma comment
======== ============= === === ===================
kernel - - - rel=3.2v5.0.7 kid=2003-02-18
cpu - - - unit=1 family=15 type=Intel Xeon
cpuid - - - unit=1 vend=GenuineIntel tfms=0:15:2:9(11)
fpu - 13 - unit=1 type=80387-compatible
pci 0xcf8-0xcff - - am=1 sc=0 buses=3
PnP - - - nodes=0
clock - - - type=TSC/2.392032383Ghz
serial 0x3f8-0x3ff 4 - unit=0 type=Standard nports=1 base=0 16550A/16
console - - - unit=vga type=0 num=12 scoansi=1 scroll=50
adapter 0xd800-0xd8ff 11 - type=ad160 ha=0 slot=0 bus=0 id=7 fts=sto
adapter 0xdc00-0xdcff 3 - type=ad160 ha=1 slot=0 bus=0 id=7 fts=sto
floppy 0x3f2-0x3f7 6 2 unit=0 type=135ds18
udi - - - UDI environment
adapter - - - ha=0 type=usb_msto UDI SCSI HBA
adapter 0x170-0x177 15 - type=IDE ctlr=secondary dvr=wd
bcme0 - 3 - chip=BCM5703 mem=FCD00000 phy=BCM5703 ddr=00:10: 18:06:49:56
cd-rom - - - type=IDE unit=0 ctlr=sec cfg=mst dvr=Srom->wd
disk - - - type=S ha=0 id=0 lun=0 bus=0 ht=ad160 unit=0
Sdsk - - - cyls=4427 hds=255 secs=63 unit=0 fts=stdb
Sdsk-0 - - - Vnd=SEAGATE Prd=ST336753LW Rev=DX10
usb_ohci - 5 - PCI bus=0 dev=15 func=2
I am using Lone tar as the backup software and it doesn't recognize the tape when I do a scan.
8 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi,
I need to restore my tape backup, when I type "tape status" it gives;
status : ready beginning-of-tape write-protected
soft errors : 0
hard errors : 0
underruns : 3
but... (4 Replies)
Discussion started by: alisevA3
4 Replies
2. Gentoo
Hello All,
I am pretty new to Linux,
When trying to install TurboLinux 6.0 through a boot floppy,
After a while it says to insert the CD and later it is not recognizing the CDROM,
SO do we need to mount the CD-ROM before installation ??
Thanks in Advance :)
S (13 Replies)
Discussion started by: sbasetty
13 Replies
3. AIX
I have tape drive in one Lpar. when i saw that time tape is in defined state. After that i deleted the tape drive using the rmdev -R command. Then fired the cfgmgr -v command. But I am not getting the tape drive. Now the drive is even not in defined state also. It is not shown the tape drive. How... (1 Reply)
Discussion started by: pernasivam
1 Replies
4. Solaris
Recently we had a problem with a CPU card on our SunFire V880 which has Solaris 9 OS. we removed the card and there was also a problem with our usr which was accidentally deleted. We able to restore the usr but now we having a problem with our tape drive.
Previously we could write to the with
... (5 Replies)
Discussion started by: rahmantanko
5 Replies
5. UNIX for Dummies Questions & Answers
Currenty running SCO Openserver 6 at a Dell PowerEdge T300. I recently installed a driver for an Adaptec SCSI card (adpu320). When I connect a tape drive to it and re-start the system,it freezes and displays the following message: "WARNING: adpu320: Command timed out (ha= 4)" and the system... (2 Replies)
Discussion started by: RicardoM
2 Replies
6. Solaris
Hey folks,
Linux admin here, forced to use Opensolaris to try to use ufsdump/ufsrestore to get some data of some old tapes.
I've got Opensolaris 2009.06 on x86 and a Sony SDX-700V.
As a "control" experiment, I booted the system with a Linux live CD and the tape drive worked perfectly.
... (2 Replies)
Discussion started by: eddy_sysad
2 Replies
7. HP-UX
I have used ioscan -fnC tape and the system identified the tape drive. what is the command to show a listing of what is on the tape? I have used ls /dev/rmt/rmt0 to no avail. can anyone help?
Thanks in advance (10 Replies)
Discussion started by: Randydog
10 Replies
8. Solaris
Got an informix DB that won't start because DB chunk is offline. Its a raw device. See below:-
lrwxrwxrwx 1 root root 29 Feb 6 2013 /dev/DB -> /devices/pseudo/md@0:0,10,raw
How do I tell what that refers to? I've checked metadb and metastat and cant see any issues? (2 Replies)
Discussion started by: psychocandy
2 Replies
LEARN ABOUT DEBIAN
fntsample
fntsample(1) General Commands Manual fntsample(1)
NAME
fntsample - PDF and PostScript font samples generator
SYNOPSIS
fntsample [ OPTIONS ] -f FONT-FILE -o OUTPUT-FILE
fntsample -h
DESCRIPTION
fntsample program can be used to generate font samples that show Unicode coverage of the font and are similar in appearance to Unicode
charts. Samples can be saved into PDF (default) or PostScript file.
OPTIONS
fntsample supports the following options.
--font-file, -f FONT-FILE
Make samples of FONT-FILE.
--font-index, -n IDX
Font index for FONT-FILE specified using --font-file option. Useful for files that contain multiple fonts, like TrueType Collec-
tions (.ttc). By default font with index 0 is used.
--output-file, -o OUTPUT-FILE
Write output to OUTPUT-FILE.
--other-font-file, -d OTHER-FONT
Compare FONT-FILE with OTHER-FONT. Glyphs added to FONT-FILE will be highlighted.
--other-index, -m IDX
Font index for OTHER-FONT specified using --other-font-file option.
--postscript-output, -s
Use PostScript format for output instead of PDF.
--svg, -g
Use SVG format for output. The generated document contains one page. Use range selection options to specify which.
--print-outline, -l
Print document outlines data to standard output. This data can be used to add outlines (aka bookmarks) to resulting PDF file with
pdfoutline program.
--include-range, -i RANGE
Show characters in RANGE.
--exclude-range, -x RANGE
Do not show characters in RANGE.
--style, -t "STYLE: VAL"
Set STYLE to value VAL. Run fntsample with option --help to see list of styles and default values.
--help, -h
Display help text and exit.
Parameter RANGE for -i and -x can be given as one integer or a pair of integers delimited by minus sign (-). Integers can be specified in
decimal, hexadecimal (0x...) or octal (0...) format. One integer of a pair can be missing (-N can be used to specify all characters with
codes less or equal to N, and N- for all characters with codes greather or equal to N). Multiple -i and -x options can be used.
EXAMPLES
Make PDF samples for font.ttf and write them to file samples.pdf:
fntsample -f font.ttf -o samples.pdf
Make PDF samples for font.ttf, compare it with oldfont.ttf and highlight new glyphs. Write output to file samples.pdf:
fntsample -f font.ttf -d oldfont.ttf -o samples.pdf
Make PostScript samples for font.ttf and write output to file samples.ps. Show only glyphs for characters with codes less or equal to
U+04FF but exclude U+0370-U+03FF:
fntsample -f font.ttf -s -o samples.ps -i -0x04FF -x 0x0370-0x03FF
Make PDF samples for font.ttf and save output to file samples.pdf adding outlines to it:
fntsample -f font.ttf -o temp.pdf -l > outlines.txt
pdfoutline temp.pdf outlines.txt samples.pdf
AUTHOR
Copyright (C) 2007 Eugeniy Meshcheryakov <eugen@debian.org>
Homepage: <http://fntsample.sourceforge.net/>
SEE ALSO
pdfoutline(1)
2010-10-14 fntsample(1)