06-08-2009
We had this issue on two T2000 servers, and were getting rebooted occationally(at least once in a week). No logs were left behind. Sun did not find any resolution, and hooked up a permanent display console to capture any logs...nothing found..and server got bounced again...siliently..leaving no logs. :-) ..like a suspense story
Finally, the issue went away after having the System Board replaced.
10 More Discussions You Might Find Interesting
1. Solaris
Hi
I am fresher in Virtualisation in solaris 10.I need to know how to install and configure guest OS, I have a server Sun T2000 with solaris 10 OS BASE.
How to install logical domain, what are the prerequest for installing l domain
can some one guide me what are the basic requirement to... (2 Replies)
Discussion started by: solaris8in
2 Replies
2. Solaris
I can't find why but I suppose it is because of some hardware failures... I have a Sun Fire V490 with Solaris 10 5/08 which runs Sun Cluster 3.2 and it downs occasionally with a circumstances I can't define... Also I note some strange behavior after server failures: when I ran any diagnostics from... (6 Replies)
Discussion started by: Sapfeer
6 Replies
3. Solaris
Hi All
I have a problem on T2000 server.
bash-3.00# uname -a
SunOS 5.10 aaa Generic_120011-14 sun4v sparc SUNW,Netra-T2000After the initial solaris installation server failed to boot:
Rebooting with command: boot
Boot device: disk:b File and args:
The file just loaded does not appear... (1 Reply)
Discussion started by: ouzist
1 Replies
4. Solaris
Hi Guys,
I am unable to turn on the locator led light on a SUN T2000 machine
# uname -a
SunOS node1 5.10 Generic_137137-09 sun4v sparc SUNW,Sun-Fire-T200
when i try to turn it on I have following error.
# locator -n
'system' locator not found
Although the hardware specfication... (5 Replies)
Discussion started by: Asteroid
5 Replies
5. Solaris
This may be a stupid question, but I don't want to take any chances.
I have a Sun T2000 in production. I want to run the "resetsc" command on the ALOM controller to active an IP address change. Will resetting ALOM affect the running OS?
Thanks (2 Replies)
Discussion started by: soliberus
2 Replies
6. Hardware
Hi All
I have a Sun T2000 server. Couple of years ago I had configured and mirrored the boot drive with an other drive using hardware RAID 1 using raidctl command.
Following is the hardware RAID output.
root@oracledatabaseserver / $ raidctl
RAID Volume RAID RAID Disk... (0 Replies)
Discussion started by: Tirmazi
0 Replies
7. Solaris
I got a Power supply failure. I replaced the power supply and still got the error.
Any ideas on what I should try next? (1 Reply)
Discussion started by: 642fiddi
1 Replies
8. Solaris
Hi,
Would like to know the uptime or specific time limit to reboot the sun microsystem to avoid unplanned outage.
Regards,Tarun (9 Replies)
Discussion started by: taruntan
9 Replies
9. Solaris
Hi folks,
I was patching Sun server (SunOS suns121 5.10 Generic_144488-17 sun4v sparc SUNW,Sun-Fire-T200) with the lateset bundle. It was completed with no errors. Server was restarted with shutdown command
(/usr/sbin/shutdown -y -i6 -g0) after patching was complete. However, after that,... (3 Replies)
Discussion started by: zulu1
3 Replies
10. Solaris
==============================
ALOM BOOTMON v1.3.1
ALOM Build Release: 001
Reset register: f0000000 EHRS ESRS LLRS SWRS
ALOM POST 1.0
Dual Port Memory Test, PASSED.
TTY External - Internal Loopback Test
TTY External - Internal Loopback Test, PASSED.
TTYC - Internal Loopback Test
TTYC -... (4 Replies)
Discussion started by: Sameer Naik
4 Replies
LEARN ABOUT DEBIAN
getbuildlog
GETBUILDLOG(1) General Commands Manual GETBUILDLOG(1)
NAME
getbuildlog - download build logs from Debian auto-builders
SYNOPSIS
getbuildlog package [version-pattern] [architecture-pattern]
DESCRIPTION
getbuildlog downloads build logs of package from Debian auto-builders. It downloads build logs of all versions and for all architectures if
version-pattern and architecture-pattern are not specified or empty, otherwise only build logs whose versions match version-pattern and
build logs whose architectures match architecture-pattern will be downloaded. The version and architecture patterns are interpreted as
extended regular expressions as described in grep(1).
If version-pattern is "last" then only the logs for the most recent version of package found on buildd.debian.org will be downloaded.
If version-pattern is "last-all" then the logs for the most recent version found on each build log index will be downloaded.
OPTIONS
-h, --help
Show usage information and examples.
-V, --version
Show version and copyright information.
EXAMPLES
getbuildlog hello 2.2-1 amd64
Download amd64 build log for hello version 2.2-1.
getbuildlog glibc "" mips.*
Download mips(el) build logs of all glibc versions.
getbuildlog wesnoth .*bpo.*
Download all build logs of backported wesnoth versions.
AUTHOR
Written by Frank S. Thomas <fst@debian.org>.
DEBIAN
Debian Utilities GETBUILDLOG(1)