06-02-2009
ndd -set <device path> adv_1000hdx_cap 1
ndd -set <device path> adv_1000hdx_cap 0
ndd -set <device path> adv_autoneg_cap 0
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I'm way confused. I loaded RH 7.1 on an old P-75 Compaq. IT has an EtherExpress pro/100 card in it and I have that attached to the optional port on our firewall with a crossover....I can't seem to get the card to negotiate with the firewall...it's currently 100Meg at Half duplex. I'm at a loss... (3 Replies)
Discussion started by: kwalter
3 Replies
2. UNIX for Dummies Questions & Answers
Hi everybody,
I want to know if there is a command for solaris or linux to have nic answers, like:
register entity
technical contact
an so on, for a domain.
I know I can do that fron the nic's site, but some guy told me there is a command to do that, but I forget it.
I try dig, host,... (2 Replies)
Discussion started by: piltrafa
2 Replies
3. Solaris
Hi Guys,
I need help with ndd.
I was going through network FAQ but i have more questions then answers regarding ndd.
#ndd -set /dev/hme instance 0
#ndd -set /dev/hme adv_100fdx_cap 1
#ndd -set /dev/hme adv_100hdx_cap 0
#ndd -set /dev/hme adv_10fdx_cap 0
#ndd -set /dev/hme adv_10hdx_cap 0... (2 Replies)
Discussion started by: nitinkgoud
2 Replies
4. IP Networking
I have eth1 and eth2 NIC in my Ubuntu. Everything works fine. I have two static IP, on XP and Ubuntu. XP - 192.168.0.1, Ubuntu is 192.168.0.2 on eth1, eth2 is set on DHCP. I have Lan on and internet sharing. I share internet over XP. Can somebody explain to me some things: I assume that eth1 is my... (2 Replies)
Discussion started by: salvor_hardin
2 Replies
5. UNIX for Dummies Questions & Answers
Folks;
I have 2 NIC cards on my SUSE Linux server. One of them was reporting receive errors for a while now it's OK, but i'd like to monitor it.
Is there any command i can run to tell me the usage in the past or give me a history of traffic and the speed that going on this specific card?
I... (1 Reply)
Discussion started by: Katkota
1 Replies
6. Solaris
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies
7. IP Networking
I am new in squid proxy.
My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)?
Thank you in advance! (4 Replies)
Discussion started by: aixlover
4 Replies
8. Red Hat
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies
9. Linux
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
ndd(1M) System Administration Commands ndd(1M)
NAME
ndd - get and set driver configuration parameters
SYNOPSIS
ndd [-set] driver parameter [value]
DESCRIPTION
ndd gets and sets selected configuration parameters in some kernel drivers. Currently, ndd only supports the drivers that implement the
TCP/IP Internet protocol family. Each driver chooses which parameters to make visible using ndd. Since these parameters are usually
tightly coupled to the implementation, they are likely to change from release to release. Some parameters may be read-only.
If the -set option is omitted, ndd queries the named driver, retrieves the value associated with the specified parameter, and prints it. If
the -set option is given, ndd passes value, which must be specified, down to the named driver which assigns it to the named parameter.
By convention, drivers that support ndd also support a special read-only parameter named ``?'' which can be used to list the parameters
supported by the driver.
EXAMPLES
Example 1: Getting Parameters Supported By The TCP Driver
To see which parameters are supported by the TCP driver, use the following command:
example% ndd /dev/tcp ?
The parameter name ``?'' may need to be escaped with a backslash to prevent its being interpreted as a shell meta character.
The following command sets the value of the parameter ip_forwarding in the dual stack IP driver to zero. This disables IPv4 packet forward-
ing.
example% ndd -set /dev/ip ip_forwarding 0
Similarly, in order to disable IPv6 packet forwarding, the value of parameter ip6_forwarding
example% ndd -set /dev/ip ip6_forwarding 0
To view the current IPv4 forwarding table, use the following command:
example% ndd /dev/ip ipv4_ire_status
To view the current IPv6 forwarding table, use the following command:
example% ndd /dev/ip ipv6_ire_status
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
SEE ALSO
nca(1), ioctl(2), attributes(5), arp(7P), ip(7P), ip6(7P), tcp(7P), udp(7P)
NOTES
The parameters supported by each driver may change from release to release. Like programs that read /dev/kmem, user programs or shell
scripts that execute ndd should be prepared for parameter names to change.
The ioctl() command that ndd uses to communicate with drivers is likely to change in a future release. User programs should avoid making
dependencies on it.
The meanings of many ndd parameters make sense only if you understand how the driver is implemented.
SunOS 5.10 8 Nov 1999 ndd(1M)