05-29-2009
Add an appropriate route.
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
We are trying to Establish Network using Linux.Now we are facing the problem in configring Ethernet.In out network we are giving eth0 in server and activating it at the boot time,so it is activating as it is but when we define the Ethernet of node on server and allowing it to activate at boot time... (5 Replies)
Discussion started by: at_renai2001
5 Replies
2. UNIX for Dummies Questions & Answers
I am using Red Hat 7.1 . I have installed one Server and trying to make network installing workstations on other system of a network. The Ethernet of the server has been mounted and working properly. I am getting problem installing /mounting the Ethernet of the workstations .I have tryed this by... (1 Reply)
Discussion started by: at_renai2001
1 Replies
3. Cybersecurity
I suspect that someone is using a sniffer on my Ethernet connection,
OS X 10.3.9, DSL,
ok, I'm in terminal using the "ifconfig" command >
flags=8049<UP,LOOPBACK,RUNNING,MULTICAST>mtu 16384
right, it's not in "promiscuous mode", but i think it's Trojaned, can anyone point me in the... (1 Reply)
Discussion started by: su"do"er
1 Replies
4. UNIX for Advanced & Expert Users
I understand that one should setup virtual ethernet adapters in the lpars which is the best way for various lpars to communicate with each other - Does anyone have info on this or can point me to a doc that explains how to set this up? (1 Reply)
Discussion started by: capeme
1 Replies
5. IP Networking
What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies
6. Solaris
Boot device: /pci@8,600000/SUNW,qlc@4/fp@0,0/disk@w500000e0103c3391,0:a File and args:
SunOS Release 5.8 Version Generic_108528-29 64-bit
Copyright 1983-2003 Sun Microsystems, Inc. All rights reserved.
ifconfig: plumb: qfe2: Bad file number
configuring IPv4 interfaces: eri0.
moving addresses... (1 Reply)
Discussion started by: fredginting
1 Replies
7. AIX
Hello everyone
I have a problem with one server, has Aix 5.3 in the errpt has this message
IDENTIFIER TIMESTAMP T C RESOURCE_NAME DESCRIPTION
F3931284 0105133009 I H ent0 ETHERNET NETWORK RECOVERY MODE
EC0BCCD4 0105133009 T H ent0 ETHERNET DOWN
F3931284 ... (4 Replies)
Discussion started by: lo-lp-kl
4 Replies
8. AIX
Hi
In the vio server when I do # lsattr -El hdisk*, I get a PVID. The same PVID is also seen when I put the lspv command on the vio client partition. This way Im able to confirm the lun using the PVID.
Similarly how does the vio client partition gets the virtual ethernet scsi client adapter... (1 Reply)
Discussion started by: newtoaixos
1 Replies
9. Linux
I need to enable Ethernet Bonding on three systems, connected together via switch. What I tried ended up with failure, slaves cannot be detected n added to bon0.
Here's what I did:
created file /etc/modprobe.d/bonding.d and added the following to it:
alias bond0 bonding
options bonding... (2 Replies)
Discussion started by: dr_mabuse
2 Replies
LEARN ABOUT REDHAT
pvm_mstat
MSTAT(3PVM) PVM Version 3.4 MSTAT(3PVM)
NAME
pvm_mstat - Returns the status of a host in the virtual machine.
SYNOPSIS
C int mstat = pvm_mstat( char *host )
Fortran call pvmfmstat( host, mstat )
PARAMETERS
host Character string containing the host name.
mstat Integer returning machine status:
value MEANING
PvmOk host is OK
PvmNoHost host is not in virtual machine
PvmHostFail host is unreachable (and thus possibly failed)
DESCRIPTION
The routine pvm_mstat returns the status mstat of the computer named host with respect to running PVM processes. This routine can be used
to determine if a particular host has failed and if the virtual machine needs to be reconfigured. The function pvm_notify() can also be
used to notify the caller that a host has failed.
EXAMPLES
C:
mstat = pvm_mstat( "msr.ornl.gov" );
Fortran:
CALL PVMFMSTAT( 'msr.ornl.gov', MSTAT )
ERRORS
These error conditions can be returned by pvm_mstat
PvmSysErr
pvmd not responding.
PvmNoHost
giving a host name not in the virtual machine.
PvmHostFail
host is unreachable (and thus possibly failed).
SEE ALSO
pvm_notify(3PVM), pvm_config(3PVM)
30 August, 1993 MSTAT(3PVM)