I have SCO Unix. I have 2 routers. as it is now, when someone telnets to UNIX and goes through router #1 everything is fine. The users who go through router #2 can not connect at all. I talked to CISCO and they said I need to set up a second Gateway on UNIX. They said what is happening is that... (1 Reply)
ok i configured my gateway and IP address(es) using ifconfig and route.. but how can i bind unique IPs to users ? (im using FreeBSD 4.2 RELEASE #3) (9 Replies)
Can anyone help with the following;
I am working on a unix server (Apple OS X Server). We have two network cards in the server. Both cards are on different subnets i.e en1 is on 192.168.10.10/24 and the built in ethernet is on 10.10.150.10/24. From a computer plugged into en1 (and set to ip... (5 Replies)
Hello,
I would like to modify my firewall configuration for being able to handle 2 internet connections in my Red zone.
I would then like to configure some selecting routing rules depending on the internal source.
Actual configuration:
=====================
1 router A (ISP)... (1 Reply)
Hello Friends
I have two network cards
eth0 192.168.100.1
eth1 10.0.0.1
There NIC connect with diff. LAN
I want to make my Linux machine as a Router, Please tell me
using
IPTABLES command
ROUTE command
:) (2 Replies)
I am using RedHat Linux 9, In this box their are two lan intefaces.
eth0 ====> LAN
192.168.100.100
255.255.255.0
eth1 ====> Internet
Static IP
255.255.255.0
59.144.168.226 (Gateway)
I want to define a gateway 59.144.168.226 for my LAN... (2 Replies)
Hey guys,
I needed to add a route to my routing table and I got it to work but on reboot it gets removed. Anyone know what file I can add this route to so it stays on the machine after a reboot? (9 Replies)
Hello everybody,
I need help:
I have to make routing between two different LAN.
I have the IP for first network 81.180.75.70 and the mask is 255.255.255.192
and for the second network: 192.168.1.1 and the mask 255.255.255.0
So, each network has only one PC with windows (this is for test),... (0 Replies)
Discussion started by: meorfi
0 Replies
LEARN ABOUT SUSE
ifndp-proxy
IFNDP-PROXY(5) Network configuration IFNDP-PROXY(5)NAME
ifndp-proxy[-<interface name>] - IPv6 NDP and IPv4 ARP proxy entries
SYNOPSIS
/etc/sysconfig/network/ifndp-proxy
/etc/sysconfig/network/ifndp-proxy-<interface name>
DESCRIPTION
These files contain IPv6 NDP and IPv4 ARP proxy settings, that should be applied using the ip neigh add proxy command documented in the
ip(8) manual page that provides a common interface for IPv4 and IPv6.
The NDP/ARP proxy is required, e.g. when IP addresses from the same subnet have to be used on the interface of the host as well as on
interfaces behind a (tunnel) interface and using a bridge is not an option.
Don't forget to enable forwarding and the NDP/ARP proxy by setting
net.ipv6.conf.<all|default|interface name>.proxy_ndp = 1
net.ipv6.conf.<all|default|interface name>.forwarding = 1
and/or
net.ipv4.conf.<all|default|interface name>.proxy_arp = 1
net.ipv4.conf.<all|default|interface name>.forwarding = 1
or
net.ipv4.ip_forward = 1
either as global all setting in the /etc/sysctl.conf file or using the ifsysctl(5) files, that allow per-interface setup.
Forwarding can be also enabled in the /etc/sysconfig/sysctl file using the IP_FORWARD and IPV6_FORWARD variables.
The proxy entries are added and deleted using the if-{up|down}.d/ndp-proxy script, every time after an involved interface has been set
up or down.
SYNTAX
The format of the ifndp-proxy file is:
<address> <address interface> <proxy interface list>
The format of the ifndp-proxy-<address interface> file is same to above, but allows also to omit the address interface by using a "-" as
placeholder inside of the file, because it is already available in the file name:
<address> <address interface | -> <proxy interface list>
Lines beginning with # and blank lines are ignored.
Each line defines to add a proxy NDP/ARP entry with the address of or behind address interface to all interfaces in the proxy interface
list.
EXAMPLES
Let's assume, your machine is connected via eth0 to a switch with the networks 2001:db8:abba::/64 and 192.168.100.1/24 and is using the IP
address 1 itself. You'd like to use the addresses 11 and 12 e.g. for virtual machines behind the tap1 and tap2 interface, that is:
2001:db8:abba::1/64 -- local eth0 address
2001:db8:abba::11/64 -- address behind tap1
2001:db8:abba::12/64 -- address behind tap2
192.168.100.1/24 -- local eth0 address
192.168.100.11/24 -- address behind tap1
192.168.100.12/24 -- address behind tap2
then set up the following entries in the ifndp-proxy file:
2001:db8:abba::1 eth0 tap1 tap2
2001:db8:abba::11 tap1 eth0 tap2
2001:db8:abba::12 tap2 eth0 tap1
192.168.100.1 eth0 tap1 tap2
192.168.100.11 tap1 eth0 tap2
192.168.100.12 tap2 eth0 tap1
additionally to the routing entries in the routes or ifroute-<interface name> files.
BUGS
Please report bugs at <https://bugzilla.novell.com/>
AUTHOR
Marius Tomaschewski <mt@suse.de>
SEE ALSO ifup(8)ifcfg(5)ifsysctl(8)sysconfig December 2009 IFNDP-PROXY(5)