is there any way to compare two grep commands in an if statement? like:
if grep blah = grep blah blah
then
is there a way to store the values of the greps and compare them? the greps are counting pattern matches in two different files and i need to make sure they match. (7 Replies)
Using the bash shell I am trying to read in 2 files. The first file (file1) is a list of names to search for in (file2). If a name in file1 is found in file2 I want the entire line in file2 to be printed to an output file. File1 consists of a single column of names. File2 consists of several... (2 Replies)
I want to read a log file from a particular location.In the logfile , lines contains timestamp.I need to compare the timestamp in the logfile with the current date.If the timpestamp in the log file is less than 4 hours then i need to read the file from that location.Below is the file format.Please... (1 Reply)
I want to read a log file from a particular location.In the log file each line starts with timestamp.I need to compare the timestamp in the logfile with the current date.If the timpestamp in the log file is less than 4 hours then i need to read the file from that location.Below is the file... (1 Reply)
Hi, I'm not sure if this is the right place but I'm a newb so it seemed right. I'm trying to write some code to organize JPEGs. Its a long story, but essentially, I need the program to tell me whether a particular jpeg is of 1) a sheet of paper (lets say its solid pink that takes up the entire... (3 Replies)
I have four files, I need to compare these files together.
As such i know "sdiff and comm" commands but these commands compare 2 files together. If I use sdiff command then i have to compare each file with other which will increase the codes.
Please suggest if you know some commands whcih can... (6 Replies)
If ($argv == “-debug”) then
Echo “in loop”
Endif
But this is not working. If I modify this code and remove “-“, then it works.
Similarly I am getting problem using grep command also
Grep “-debug” Filename
Can someone please help me on how to resolve these... (1 Reply)
Hi All,
Need help on this
I have 2 files
one file file1 which has several entries as :
define service{
hostgroup_name !host1,!host5,!host6,.*
service_description check_nrpe
}
define service{
hostgroup_name !host2,!host4,!host6,.*
service_description check_opt
}
another... (2 Replies)
Hi dear users,
I need to compare numeric columns in two files. These files have the following structure.
K.txt (4 columns)
A001 chr21 9805831 9846011
A002 chr21 9806202 9846263
A003 chr21 9887188 9988593
A003 chr21 9887188 ... (2 Replies)
Hi guys, looking for some help with a way to compare data in two files but with some conditions.
example,
File 1 consists of
site1,10.1.1.1
site2,20.2.2.2
site3,30.3.3.3
File 2 contains
site1,l0.1.1.1
site2,50.1.1.1
site3,30.3.3.3
site4,40.1.1.1
I want to be able to match the... (1 Reply)
Discussion started by: mutley2202
1 Replies
LEARN ABOUT DEBIAN
irsend
IRSEND(1) User Commands IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.9.0-pre1 October 2010 IRSEND(1)