05-12-2009
Configure ILOM from network
HI,
Is it possible to set up ILOM from the ethernet terminal. I 'm at remote location from server so would like to know if i can configure it remotely
I'm able to access my server via ssh terminal.
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Can anybody help me on how to configure the network in Sun Solaris. This is my first time to touch sun system please help!!!:confused: :confused: (2 Replies)
Discussion started by: jameswong
2 Replies
2. UNIX for Dummies Questions & Answers
Hi,
I have a networked ultra 5 workstation(using NIS) that I would like to be able to :
1. Reconfigure to standalone workstation,
2. and be able to switch back to a network workstation when the needs required.
Please advise.
Ryan (5 Replies)
Discussion started by: ryantk
5 Replies
3. HP-UX
Hi
I'm new about UNIX, but I've to use a HP9000 with HP-UX 10.20 workstation. I'm trying to configure the network, I've configured the file /etc/rc.conf.d/netconf with my IP address and the right gateway, so the HP9000 is on the net, I've tried a ping. But now I've a problem I can't start hte CDE,... (4 Replies)
Discussion started by: gofmass
4 Replies
4. Solaris
Hi..i have installed solaris 10 on vmware. I m not able connect to internet.
pls help in detail. how to solve the problem. During the installation i have put no DHCP. cofigured manually ( Ip 192.168.1.9) default gateway 192.168.1.1 . (3 Replies)
Discussion started by: johnavery
3 Replies
5. Solaris
i have a router from my isp provider 02. my internet works fine in windows but i am unable to use internet in solaris. when i tried ifconfig command
i was able to see the lo0 which is my laoopback adapter. pls can someone advice. (7 Replies)
Discussion started by: seyiisq
7 Replies
6. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
7. Solaris
Hi Everyone,
In my environment, I have few T5220. On the iLOM Management Card, I have both Network and Serial port are cabled, I don't have any issues while I try to connect using Network Management port, but when I try to connect the serial port for the same server which is actually connected... (3 Replies)
Discussion started by: bobby320
3 Replies
8. Solaris
Hi,
I have installed Solaris 10 on VMware7, When i used ifconfig -a to check network interface, it has shown lo0 as loopback interface.
Please advise how to configure network interfaces using VMware. (1 Reply)
Discussion started by: ajhal04
1 Replies
9. Solaris
Hi,
I have a Solaris 10 zone which I need to configure on a new network. I have configured the new IP on the zone itself and I can ping the interface from a node on the same network, but not from another network. Basically I need to know how to route the traffic from the zone to it's... (3 Replies)
Discussion started by: sparcman
3 Replies
LEARN ABOUT PHP
sftp-server
sftp-server(1M) System Administration Commands sftp-server(1M)
NAME
sftp-server - SFTP server subsystem
SYNOPSIS
/usr/lib/ssh/sftp-server
DESCRIPTION
sftp-server implements the server side of the SSH File Transfer Protocol as defined in the IETF draft-ietf-secsh-filexfer.
sftp-server is a subsystem for sshd(1M) and must not be run directly. There are no options or config settings.
To enable the sftp-server subsystem for sshd add the following to /etc/ssh/sshd_config:
Subsystem sftp /usr/lib/ssh/sftp-server
See sshd_config(4) for a description of the format and contents of that file.
There is no relationship between the protocol used by sftp-server and the FTP protocol (RFC 959) provided by in.ftpd.
EXIT STATUS
The following exit values are returned:
0 Successful completion.
>0 An error occurred.
FILES
/usr/lib/sftp-server
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWsshdu |
+-----------------------------+-----------------------------+
|Interface Stability |Evolving |
+-----------------------------+-----------------------------+
SEE ALSO
sftp(1), ssh(1), ssh-add(1), ssh-keygen(1), sshd(1M), sshd_config(4), attributes(5)
To view license terms, attribution, and copyright for OpenSSH, the default path is /var/sadm/pkg/SUNWsshdr/install/copyright. If the
Solaris operating environment has been installed anywhere other than the default, modify the given path to access the file at the installed
location.
AUTHOR
Markus Friedl
SunOS 5.10 30 Jul 2003 sftp-server(1M)