05-07-2009
you have to configure the netmgmt IP from the Service Processor, check the documention on this.
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
hi !
sorry for the stupid question
but my /console is full and i need to clean it
how do i clean it ? :confused: (2 Replies)
Discussion started by: karine
2 Replies
2. UNIX for Advanced & Expert Users
We are using software (Pegasys) which runs on SunOS 5.8 and reads images from a Philips nuclear camera. The software is designed to run from the console. I need to be able to capture the images it produces on the display. The caveat is that I cannot use the X Windows display because the X Server... (3 Replies)
Discussion started by: sreyes27
3 Replies
3. Shell Programming and Scripting
hi,
how to access console of a switch having rj45 on switch side to db 9 female on pc side console cable which needs to be connected to one console server having rj11 on its side and db 9 female on other end.i.e. on switch side,console cable has rj45 and db 9 pin female connector on other side of... (1 Reply)
Discussion started by: pankajd
1 Replies
4. Solaris
I need to configure the iLOM for x4600 server. before I can set the IP details and commit, I need to set network state should be enabled. However my firmware is already the latest and I need not upgrade. I am not able to set the /SP/network state to enable. pls assist. i BELIEVE the bug was fixed... (5 Replies)
Discussion started by: incredible
5 Replies
5. UNIX for Dummies Questions & Answers
:confused:Hi
This was installed on the Linux box a few weeks back by a guy that no longer works for us. All worked fine until last week. Now when we connect its just a blank screen with no icons.
I get a whole bunch of errors when starting the service too:
Tue Feb 23 14:29:45 2010
... (1 Reply)
Discussion started by: wbdevilliers
1 Replies
6. Solaris
One of my X4600 server had a power loss and rebooted and now its giving me a strange problem servers internal disk controller naming has changed by itself ... the after failsafe boot md.conf file shows following c3txdx but shows internal disk at c4txdx ... what could be the reason for this and... (1 Reply)
Discussion started by: fugitive
1 Replies
7. UNIX for Dummies Questions & Answers
Hi Gurus,
Can some one explain me the difference between a IP console and a serial console. (1 Reply)
Discussion started by: rama krishna
1 Replies
8. Solaris
Hi Folks,
Has anyone seen these errors on bootup.
Mar 15 12:22:30 svc.startd: svc:/system/device/local:default: Method "/lib/svc/method/devices-local" failed due to signal SEGV.ht (c) 1983, 2010,
Oracle and/or its affiliates. All rights reserved.
Configuring devices. ... (1 Reply)
Discussion started by: ESSTEAM
1 Replies
9. Hardware
Booting and checking BIOS there is no option to enable-disable hyperthreading.
I have 8 Dual-Core AMD Opteron(tm) Processor 8220 and I see 16 cores.
Enable hyperthreading I should have 32 cores.
I have red hat 5.4 installed.
Anyone know how can enable hypethreading ? I have last BIOS/Firmware... (2 Replies)
Discussion started by: laxtnog
2 Replies
10. Hardware
Hi All,
I am having an Sun fire X4600 M2 server where one of the interfaces is down.
I had requested for the replacement but had a bit problem in identifying the port.
As per the server service module, there are 4 NIC ports and one port is not flashing (e1000g0) but as per server, the port... (8 Replies)
Discussion started by: Rockyc3400
8 Replies
LEARN ABOUT SUSE
sg_emc_trespass
SG_EMC_TRESPASS(8) SG3_UTILS SG_EMC_TRESPASS(8)
NAME
sg_emc_trespass - Changes ownership of a LUN from another Service-Processor to this one.
SYNOPSIS
sg_emc_trespass [-d] [-hr] [-s] [-V] DEVICE
DESCRIPTION
sg_emc_trespass sends an EMC-specific Trespass Command to the DEVICE with the selected options. This Mode Select changes the ownership of
the LUN of the device from another Service-Processor to the one the command was received on.
OPTIONS
Arguments to long options are mandatory for short options as well.
-d outputs some extra debug information associated with executing this command
-hr Sets the 'Honor Reservation' bit in the command. If set, the trespass will only succeed to change the ownership from the Peer SP if
the Peer SP does not have an outstanding SCSI reservation for the LUN. By default, the reservation state will be ignored.
-s Send the short version of the trespass command instead of the long version. The short version is supported on the EMC FC5300, FC4500
and FC4700. The long version (default) is supported on the CLARiiON CX and AX family arrays.
-V print out version string then exit.
In the 2.4 series of Linux kernels the DEVICE must be a SCSI generic (sg) device. In the 2.6 series block devices (e.g. SCSI disks and DVD
drives) can also be specified. For example "sg_start 0 /dev/sda" will work in the 2.6 series kernels.
EXIT STATUS
The exit status of sg_emc_trespass is 0 when it is successful. Otherwise see the sg3_utils(8) man page.
AUTHOR
Written by Lars Marowsky-Bree, based on sg_start.
REPORTING BUGS
Report bugs to <dgilbert at interlog dot com>.
COPYRIGHT
Copyright (C) 2004 Lars Marowsky-Bree, Douglas Gilbert.
This software is distributed under the GPL version 2. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PUR-
POSE.
sg3_utils-1.23 January 2007 SG_EMC_TRESPASS(8)