Sponsored Content
Operating Systems Solaris BIOS Serial Number on Sun Fire V240 Post 302310221 by vineetd on Friday 24th of April 2009 05:35:07 AM
Old 04-24-2009
BIOS Serial Number on Sun Fire V240

Hi,

I want to know if there is a command available for obtaining the BIOS Serial Number on a Sun Fire V240 machine? Or is it a known issue that it cannot be obtained through any command?

Thanks,

Vineet
 

9 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

Help: Sun Disk partitioning for Sun V240 & StorEdge 3300

Dear Sun gurus, I have Sun Fire V240 server with its StorEdge 3300 disk-array. Following are its disks appeared in format command. I have prepared its partitions thru format and metainit & metattach (may be i have made wrong steps, causing the errors below because I have done thru some document... (1 Reply)
Discussion started by: shafeeq
1 Replies

2. Solaris

connecting laptop to V240 serial port

Well...I hope I am in the right forum to post this question. Here is what I am trying to do. I have a laptop (Dell I believe) running Windows. I am trying to connect this laptop to a V240 serial port (the port with l0l0l). Here lies the problem, I am not sure if I have the correct cable. I do... (6 Replies)
Discussion started by: bluridge
6 Replies

3. Solaris

Sun 280r serial number

is there a command i can run at the ksh that will give me the serial number on solaris? solaris 8, and 9 280r servers (16 Replies)
Discussion started by: BG_JrAdmin
16 Replies

4. Solaris

Sun Fire 280R Sun Solaris CRT/Monitor requirements

I am new to Sun. I brought Sun Fire 280R to practice UNIX. What are the requirements for the monitor/CRT? Will it burn out old non-Sun CRTs? Does it need LCD monitor? Thanks. (3 Replies)
Discussion started by: bramptonmt
3 Replies

5. Solaris

Sun Fire V890 - Unable to access RSC or Serial console

Hello Folks, I am having trouble to login to rsc or serial console of V890. The rsc2.2.3 has been configured with required parameters, resetrs and even rebooted. When serial port is connected to laptop, The hyper terminal does not get the console or POSt messages when the server is rebooting... (8 Replies)
Discussion started by: defflepord
8 Replies

6. Solaris

Alom Sun V240

hallo anybody know how to set alom mail alerty server with yahoomail ? thank u?where i can find mail server address for yahoomail?thank (1 Reply)
Discussion started by: yanto85
1 Replies

7. Red Hat

CLI for serial number or tag for BIOS

what file or command can be used to get information that can represent unique ID for BIOS installed, it could be serial number or some tag. I used "/usr/sbin/dmidecode | egrep -i 'BIOS Information' -A 20" command, it shows some information about BIOS but not some information that can be used as... (4 Replies)
Discussion started by: epriya2003
4 Replies

8. Hardware

Sun fire 4270 reset BIOS settings after reboot

Hello, I am trying to perform Suse 10 SP3 installation via network in 6 Sun Fire 4270 M2 servers. The problem is that even if i set first prio boot device the hard disk the system always try to boot from network.And after the first restart the BIOS setting has been lost(and PXE come first... (2 Replies)
Discussion started by: @dagio
2 Replies

9. Solaris

Sun Fire V240 server Fan replacement

I have a sun fire v240 server. The output of prtdiag -v shows a failed fan. There are 3 fans for cooling system board. There is 1 fan for each of the powersupply (There are 2 powersupplies) From the below output how do i know which fan is bad and whats its location... (3 Replies)
Discussion started by: Tirmazi
3 Replies
VPDDECODE(8)						      System Manager's Manual						      VPDDECODE(8)

NAME
vpddecode - VPD structure decoder SYNOPSIS
vpddecode [OPTIONS] DESCRIPTION
vpddecode prints the "vital product data" information that can be found in almost all IBM and Lenovo computers. Available items are: o BIOS Build ID o Box Serial Number o Motherboard Serial Number o Machine Type/Model Some systems have these additional items: o BIOS Release Date o Default Flash Image File Name Note that these additional items are not documented by IBM, so this is guess work, and as such should not be blindly trusted. Feedback about the accuracy of these labels is welcome. OPTIONS
-d, --dev-mem FILE Read memory from device FILE (default: /dev/mem) -s, --string KEYWORD Only display the value of the VPD string identified by KEYWORD. KEYWORD must be a keyword from the following list: bios-build-id, box-serial-number, motherboard-serial-number, machine-type-model, bios-release-date. Each keyword corresponds to an offset and a length within the VPD record. Not all strings may be defined on all VPD-enabled systems. If KEYWORD is not provided or not valid, a list of all valid keywords is printed and vpddecode exits with an error. This option cannot be used more than once. Mutually exclusive with --dump. -u, --dump Do not decode the VPD records, dump their contents as hexadecimal instead. Note that this is still a text output, no binary data will be thrown upon you. ASCII equivalent is displayed when possible. This option is mainly useful for debugging. Mutually exclu- sive with --string. -h, --help Display usage information and exit -V, --version Display the version and exit FILES
/dev/mem AUTHOR
Jean Delvare SEE ALSO
biosdecode(8), dmidecode(8), mem(4), ownership(8) dmidecode February 2007 VPDDECODE(8)
All times are GMT -4. The time now is 04:55 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy