Hi all
I just installed Fedora Core 3 onto my pc which is running slackware as the 'main' os
I have been using LILO as the boot loader for a long time but thought I'd swap to GRUB for a change.
Fedora boots fine.
I have a seperate /boot partition for my slackware install ......its... (0 Replies)
ok so i have two HDs on my PC, on the 1st one (master) i have w2k running, i decided to install debian on the second (slave). During the install, i was asked if i wanted to install grub, i said yes.
Now debian starts just fine. Windows on the hand now takes forever to load (ie like two minutes... (4 Replies)
in dual os grub will ask like this (linux 9 (red hat))
linux(bigmem)
linux(smallmem)
dos
so i want that grub will ask like this
dos
linux(bigmem)
linux(smallmem)
how to do this (8 Replies)
Hi, I installed solaris 10 a few weeks ago. It was working fine during the past two weeks. However, now when I start to load to the drive, I get this problem:
The BIOS screen comes up like normal, then screen goes blank and a message "Grub loading stage 2" flashes real quick then the computer... (1 Reply)
Hello
There is a > prompt at Grub, # prompt for the console and $ for bash, but I am clueless about when and how to get into a specific prompt, how to move around between one prompt to another and how to exit.
Is there a very basic guide anywhere that CLEARLY explains the type of shell... (2 Replies)
Hi,
Can we specify which grub.conf to use while installing grub on RHEL.
We are working on application which requires different grub configurations needed, depending on certain criteria we need to update grub with correct grub.conf.
Can we use grub-install for this purpose? (4 Replies)
Dear Masters,
i have a problem with unix script, till now i just know about how to create header.
i want to change file below
-63395.2 72653.5
-63361.3 72696.0 ... (9 Replies)
what if grub had a password and prevented you from getting in, what should I do, regards (2 Replies)
Discussion started by: abbya
2 Replies
LEARN ABOUT SUSE
fdformat
FDFORMAT(8) Linux Programmer's Manual FDFORMAT(8)NAME
fdformat - Low-level formats a floppy disk
SYNOPSIS
fdformat [-n] device
DESCRIPTION
fdformat does a low level format on a floppy disk. device is usually one of the following (for floppy devices, the major = 2, and the
minor is shown for informational purposes only):
/dev/fd0d360 (minor = 4)
/dev/fd0h1200 (minor = 8)
/dev/fd0D360 (minor = 12)
/dev/fd0H360 (minor = 12)
/dev/fd0D720 (minor = 16)
/dev/fd0H720 (minor = 16)
/dev/fd0h360 (minor = 20)
/dev/fd0h720 (minor = 24)
/dev/fd0H1440 (minor = 28)
/dev/fd1d360 (minor = 5)
/dev/fd1h1200 (minor = 9)
/dev/fd1D360 (minor = 13)
/dev/fd1H360 (minor = 13)
/dev/fd1D720 (minor = 17)
/dev/fd1H720 (minor = 17)
/dev/fd1h360 (minor = 21)
/dev/fd1h720 (minor = 25)
/dev/fd1H1440 (minor = 29)
The generic floppy devices, /dev/fd0 and /dev/fd1, will fail to work with fdformat when a non-standard format is being used, or if the for-
mat has not been autodetected earlier. In this case, use setfdprm(8) to load the disk parameters.
OPTIONS -n No verify. This option will disable the verification that is performed after the format.
SEE ALSO fd(4), setfdprm(8), mkfs(8), emkfs(8)AUTHOR
Werner Almesberger (almesber@nessie.cs.id.ethz.ch)
AVAILABILITY
The fdformat command is part of the util-linux-ng package and is available from ftp://ftp.kernel.org/pub/linux/utils/util-linux-ng/.
Linux 0.99 1 February 1993 FDFORMAT(8)