Sponsored Content
Full Discussion: Maximize IDE Hard Disk
Special Forums UNIX Desktop Questions & Answers Maximize IDE Hard Disk Post 302307197 by limpinmd on Tuesday 14th of April 2009 11:36:47 PM
Old 04-15-2009
Maximize IDE Hard Disk

Hi there! I am installing Unixware 7.1 to a new server. We usually use SCSI hard for this but since this will be used only for testing, I decided to use an 80GB IDE hard disk. I was able to successfully load the unix but found out that the 80GB hard disk was not maximized. The total hard disk used was about 10GB only. Is there a way to maximize the entire 80GB hard disk? By the way, during installation, i selected the option to "use the whole disk for UNIx". Thanks and regards, zap Smilie
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

The difference between SCSI & IDE Hard disks.

Hello agian ! What is the difference between SCSI and IDE hard disks ? I have Intel PC and when i check i have Generic IDE TYPE DISK0 is IDE hard disk is ok for Solrais ? or should i buy the SCSI hard disk ? Thanks Abid Malik (3 Replies)
Discussion started by: abidmalik
3 Replies

2. UNIX Desktop Questions & Answers

Hard Disk

I have a cuestion. How Can I to add other hard disk to my computer? I need to configurate anyone? (4 Replies)
Discussion started by: hmaraver
4 Replies

3. AIX

Format a Hard disk

Hello I am trying to format an extra hard disk, I want to purge all data. Does any one know how to do this, I found a format command but it only works for floppies , also related to do this how do you defrag ? I am running AIX 5.3 Thanks (1 Reply)
Discussion started by: mrmeswani
1 Replies

4. AIX

IDE DISK ERR2 and LVM SA STALEPP errors in errpt

Hi, I'm getting the errors below in the errpt report for a IBM Blade server. I'm guessing there's a problem with one of the disks but don't know how I can confirm this. Can anyone offer any suggestions? Regards Gareth (4 Replies)
Discussion started by: m223464
4 Replies

5. Filesystems, Disks and Memory

shift hard disk from primary IDE channel to secondary IDE channal

Wellcomes All, some times ago I 've installed a Debian ditribution on an Hard Disk who was set as Primary Master. Few days ago, I 've decided to install another Hard Disk with a different Operating System. When I did that, I turned off the old hard disk, and I mouted the new one on the Primary IDE... (1 Reply)
Discussion started by: thekarsillo
1 Replies

6. Solaris

problem after adding new ide disk

Hi experts, i have added a new disk to my ultra 10 system, after that i am unable to boot the system, its not booting from disk neither from cd. please help! Regards (16 Replies)
Discussion started by: kumarmani
16 Replies

7. UNIX for Dummies Questions & Answers

Hard Disk at 99% Help!

:eek: I use this Solaris to run CMS a call acounting software package for my job. No one could run reports today because it said the this when you logged on "The following file systems are low, and could adversely affect server performance: File system /: 99%full" Can some one please explain... (9 Replies)
Discussion started by: mannyisme
9 Replies

8. Filesystems, Disks and Memory

Wrong BIOS IDE Settings on a SATA disk (AHCI)?

Hello, I wanted to share an experience I had today which was quite a learning experience and perhaps useful for others who may run into the issue at some point in the future. Basically, the scenario involves a OS which was installed on a machine which hardware-wise, had a SATA Drive. The... (0 Replies)
Discussion started by: septima.pars
0 Replies

9. SCO

declare disk driver for IDE hard disk

hi I've a fresh installation of SCO 5.0.7 on the IDE hard disk. For SCSI hard disk I can declare, for example blc disk driver using: # mkdev hd 0 SCSI-0 0 blc 0but it works for IDE hard disk? (3 Replies)
Discussion started by: ccc
3 Replies

10. Linux

C++ Code to Access Linux Hard Disk Sectors (with a LoopBack Virtual Hard Disk)

Hi all, I'm kind of new to programming in Linux & c/c++. I'm currently writing a FileManager using Ubuntu Linux(10.10) for Learning Purposes. I've got started on this project by creating a loopback device to be used as my virtual hard disk. After creating the loop back hard disk and mounting it... (23 Replies)
Discussion started by: shen747
23 Replies
HD(4)							     Linux Programmer's Manual							     HD(4)

NAME
hd - MFM/IDE hard disk devices DESCRIPTION
The hd* devices are block devices to access MFM/IDE hard disk drives in raw mode. The master drive on the primary IDE controller (major device number 3) is hda; the slave drive is hdb. The master drive of the second controller (major device number 22) is hdc and the slave hdd. General IDE block device names have the form hdX, or hdXP, where X is a letter denoting the physical drive, and P is a number denoting the partition on that physical drive. The first form, hdX, is used to address the whole drive. Partition numbers are assigned in the order the partitions are discovered, and only nonempty, nonextended partitions get a number. However, partition numbers 1-4 are given to the four partitions described in the MBR (the "primary" partitions), regardless of whether they are unused or extended. Thus, the first logi- cal partition will be hdX5. Both DOS-type partitioning and BSD-disklabel partitioning are supported. You can have at most 63 partitions on an IDE disk. For example, /dev/hda refers to all of the first IDE drive in the system; and /dev/hdb3 refers to the third DOS "primary" partition on the second one. They are typically created by: mknod -m 660 /dev/hda b 3 0 mknod -m 660 /dev/hda1 b 3 1 mknod -m 660 /dev/hda2 b 3 2 ... mknod -m 660 /dev/hda8 b 3 8 mknod -m 660 /dev/hdb b 3 64 mknod -m 660 /dev/hdb1 b 3 65 mknod -m 660 /dev/hdb2 b 3 66 ... mknod -m 660 /dev/hdb8 b 3 72 chown root:disk /dev/hd* FILES
/dev/hd* SEE ALSO
chown(1), mknod(1), sd(4), mount(8) COLOPHON
This page is part of release 3.44 of the Linux man-pages project. A description of the project, and information about reporting bugs, can be found at http://www.kernel.org/doc/man-pages/. Linux 1992-12-17 HD(4)
All times are GMT -4. The time now is 10:51 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy