Sponsored Content
Operating Systems Linux Do linux have a device file for ETHERNET CARD. Post 302304376 by pludi on Monday 6th of April 2009 09:28:38 AM
Old 04-06-2009
I have absolutely no idea what you want to do. Could you give us a good example? Do you want to transfer files, maybe via a secure connection? Or do you want to trace packets in user space, because this isn't possible with high-level abstractions. And what do you mean by header and trailer information?
 

10 More Discussions You Might Find Interesting

1. Filesystems, Disks and Memory

ethernet card for Solaris

Hi, How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies

2. IP Networking

RedHat and Ethernet card no like each other

I have searched this forum for solution and have drawn a blank... so I come to you for help :) I an a Win XP user that has no problem getting on internet when I am on that OS (currently on it right now ;)). I installed red hat 9 and when I use that OS, I cannot get a connection. I ran the... (10 Replies)
Discussion started by: Minnesota Red
10 Replies

3. UNIX for Dummies Questions & Answers

Ethernet card problem...

I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the... (2 Replies)
Discussion started by: Tony Empire
2 Replies

4. AIX

Add PCI ethernet card?

Hi everyone, I recently inherited an IBM RS/6000 43P 150, and it appears that the on board ethernet is dead. Can I put in a PCI ethernet card and use that as the default ethernet connection (as opposed to the one on the motherboard)? If so, what type of card can I use and how does one configure... (2 Replies)
Discussion started by: Jwoollard
2 Replies

5. SCO

Issue with a ethernet card

Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message: Fsstat:/dev/boot mounted Mounted /stand filesystem System auditing is not enabled. Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0) Dlpid:No such... (0 Replies)
Discussion started by: tazmss1
0 Replies

6. IP Networking

ethernet card

What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies

7. AIX

Utilization of Ethernet Card

Hi, is it possible to find out network utilization of etherenet card in %? Regards, Manoj (2 Replies)
Discussion started by: manoj.solaris
2 Replies

8. Solaris

Gigaswift ethernet card on reboot

I do have a server (SUNV240) with Solaris 9, it has a PCI gigaswift ethernet card for fiber with SC connector, everytime I reboot the server the card won't link up unless I unplug it and plug it back again, for remote operations this is a hassle since sometimes reboots are needed and this card... (3 Replies)
Discussion started by: xe2bss
3 Replies

9. Solaris

Problem with my Ethernet Card

Hi Gurus of Solaris. I have a problem yesterday when I was installing solaris in a x86 equipement I attached some log that I capture when I try to resolve the problem Any guru that can help please. Any command or procedure that I can run, please advice me Regards Andres (10 Replies)
Discussion started by: andresguillen
10 Replies

10. Red Hat

Unable To Activate Ethernet Network Device in RHEL 5.5 - e100 device eth0 does not seem to be presen

Hi All, Could anyone please help to resolve the below problem. I installed RHEL5.5 in my desktop.But when i try to activate the ethernet connection then it gives me the error. I spent 2 days for the above and go through with several suggestion found by googling. But no luck. ... (0 Replies)
Discussion started by: Tanmoy
0 Replies
ADDPART(8)                                                     System Administration                                                    ADDPART(8)

NAME
addpart - tell the kernel about the existence of a partition SYNOPSIS
addpart device partition start length DESCRIPTION
addpart tells the Linux kernel about the existence of the specified partition. The command is a simple wrapper around the "add partition" ioctl. This command doesn't manipulate partitions on a block device. PARAMETERS
device The disk device. partition The partition number. start The beginning of the partition (in 512-byte sectors). length The length of the partition (in 512-byte sectors). SEE ALSO
delpart(8), fdisk(8), parted(8), partprobe(8), partx(8) AVAILABILITY
The addpart command is part of the util-linux package and is available from https://www.kernel.org/pub/linux/utils/util-linux/. util-linux January 2015 ADDPART(8)
All times are GMT -4. The time now is 02:26 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy