04-06-2009
I have absolutely no idea what you want to do. Could you give us a good example? Do you want to transfer files, maybe via a secure connection? Or do you want to trace packets in user space, because this isn't possible with high-level abstractions. And what do you mean by header and trailer information?
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
Hi,
How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies
2. IP Networking
I have searched this forum for solution and have drawn a blank... so I come to you for help :)
I an a Win XP user that has no problem getting on internet when I am on that OS (currently on it right now ;)). I installed red hat 9 and when I use that OS, I cannot get a connection. I ran the... (10 Replies)
Discussion started by: Minnesota Red
10 Replies
3. UNIX for Dummies Questions & Answers
I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the... (2 Replies)
Discussion started by: Tony Empire
2 Replies
4. AIX
Hi everyone, I recently inherited an IBM RS/6000 43P 150, and it appears that the on board ethernet is dead. Can I put in a PCI ethernet card and use that as the default ethernet connection (as opposed to the one on the motherboard)? If so, what type of card can I use and how does one configure... (2 Replies)
Discussion started by: Jwoollard
2 Replies
5. SCO
Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message:
Fsstat:/dev/boot mounted
Mounted /stand filesystem
System auditing is not enabled.
Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0)
Dlpid:No such... (0 Replies)
Discussion started by: tazmss1
0 Replies
6. IP Networking
What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies
7. AIX
Hi,
is it possible to find out network utilization of etherenet card in %?
Regards,
Manoj (2 Replies)
Discussion started by: manoj.solaris
2 Replies
8. Solaris
I do have a server (SUNV240) with Solaris 9, it has a PCI gigaswift ethernet card for fiber with SC connector, everytime I reboot the server the card won't link up unless I unplug it and plug it back again, for remote operations this is a hassle since sometimes reboots are needed and this card... (3 Replies)
Discussion started by: xe2bss
3 Replies
9. Solaris
Hi Gurus of Solaris.
I have a problem yesterday when I was installing solaris in a x86 equipement
I attached some log that I capture when I try to resolve the problem
Any guru that can help please.
Any command or procedure that I can run, please advice me
Regards
Andres (10 Replies)
Discussion started by: andresguillen
10 Replies
10. Red Hat
Hi All,
Could anyone please help to resolve the below problem.
I installed RHEL5.5 in my desktop.But when i try to activate the ethernet connection then it gives me the error.
I spent 2 days for the above and go through with several suggestion found by googling. But no luck.
... (0 Replies)
Discussion started by: Tanmoy
0 Replies
LEARN ABOUT DEBIAN
traceends
TRACEENDS(1) User Commands TRACEENDS(1)
NAME
traceends - summarise traffic done by every endpoint observed in a trace
SYNOPSIS
tracetopends [ -f bpf | --filter=bpf] [ -a addrtype | --address=addrtype] [ -H | --help]
inputuri [inputuri ...]
DESCRIPTION
traceends reports the number of bytes and packets sent and received by each endpoint observed in the input trace(s). Usually, you don't
want to run this program directly -- see tracetopends instead.
-f bpf filter
output only packets that match tcpdump style bpf filter
-A address type
Specifies how an endpoint should be defined. Suitable options are "mac", "v4" and "v6" which will report endpoint stats for each
observed MAC address, IPv4 address and IPv6 address respectively.
OUTPUT
Output is written to stdout in columns separated by blank space.
The columns are (in order):
* Endpoint address
* Time last observed
* Packets originating from the endpoint
* Bytes originating from the endpoint (IP header onwards)
* Payload originating from the endpoint (post transport header)
* Packets sent to the endpoint
* Bytes sent to the endpoint (IP header onwards)
* Payload sent to the endpoint (post transport header)
EXAMPLES
Get stats for each individual MAC address in a trace:
traceends -a mac erf:trace.erf.gz
LINKS
More details about traceends (and libtrace) can be found at http://www.wand.net.nz/trac/libtrace/wiki/UserDocumentation
SEE ALSO
libtrace(3), tracemerge(1), tracefilter(1), traceconvert(1), tracesplit_dir(1), tracereport(1), tracertstats(1), tracestats(1), tracepkt-
dump(1), traceanon(1), tracesummary(1), tracereplay(1), tracediff(1), tracetopends(1)
AUTHORS
Shane Alcock <salcock@cs.waikato.ac.nz>
traceends (libtrace) September 2011 TRACEENDS(1)