04-06-2009
I have absolutely no idea what you want to do. Could you give us a good example? Do you want to transfer files, maybe via a secure connection? Or do you want to trace packets in user space, because this isn't possible with high-level abstractions. And what do you mean by header and trailer information?
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
Hi,
How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies
2. IP Networking
I have searched this forum for solution and have drawn a blank... so I come to you for help :)
I an a Win XP user that has no problem getting on internet when I am on that OS (currently on it right now ;)). I installed red hat 9 and when I use that OS, I cannot get a connection. I ran the... (10 Replies)
Discussion started by: Minnesota Red
10 Replies
3. UNIX for Dummies Questions & Answers
I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the... (2 Replies)
Discussion started by: Tony Empire
2 Replies
4. AIX
Hi everyone, I recently inherited an IBM RS/6000 43P 150, and it appears that the on board ethernet is dead. Can I put in a PCI ethernet card and use that as the default ethernet connection (as opposed to the one on the motherboard)? If so, what type of card can I use and how does one configure... (2 Replies)
Discussion started by: Jwoollard
2 Replies
5. SCO
Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message:
Fsstat:/dev/boot mounted
Mounted /stand filesystem
System auditing is not enabled.
Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0)
Dlpid:No such... (0 Replies)
Discussion started by: tazmss1
0 Replies
6. IP Networking
What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies
7. AIX
Hi,
is it possible to find out network utilization of etherenet card in %?
Regards,
Manoj (2 Replies)
Discussion started by: manoj.solaris
2 Replies
8. Solaris
I do have a server (SUNV240) with Solaris 9, it has a PCI gigaswift ethernet card for fiber with SC connector, everytime I reboot the server the card won't link up unless I unplug it and plug it back again, for remote operations this is a hassle since sometimes reboots are needed and this card... (3 Replies)
Discussion started by: xe2bss
3 Replies
9. Solaris
Hi Gurus of Solaris.
I have a problem yesterday when I was installing solaris in a x86 equipement
I attached some log that I capture when I try to resolve the problem
Any guru that can help please.
Any command or procedure that I can run, please advice me
Regards
Andres (10 Replies)
Discussion started by: andresguillen
10 Replies
10. Red Hat
Hi All,
Could anyone please help to resolve the below problem.
I installed RHEL5.5 in my desktop.But when i try to activate the ethernet connection then it gives me the error.
I spent 2 days for the above and go through with several suggestion found by googling. But no luck.
... (0 Replies)
Discussion started by: Tanmoy
0 Replies
LEARN ABOUT ULTRIX
uuencode
uuencode(5) File Formats Manual uuencode(5)
Name
uuencode - format of an encoded uuencode file
Description
Files output by consist of a header line, followed by a number of body lines, and a trailer line. The command ignores any lines preceding
the header or following the trailer. Lines preceding a header must not, of course, look like a header.
The header line is distinguished by having the first six characters by the word ``begin'', followed by a space. The next item on the line
is a mode (in octal) and a string which names the remote file. A space separates the three items in the header line.
The body consists of a number of lines, each at most 62 characters long including the trailing new line. These consist of a character
count, followed by encoded characters, followed by a new line. The character count is a single printing character and represents an inte-
ger, the number of bytes the rest of the line represents. Such integers are always in the range from 0 to 63 and can be determined by sub-
tracting the character space (octal 40) from the character.
Groups of 3 bytes are stored in 4 characters, with 6 bits per character. All are offset by a space to make the characters print. The last
line may be shorter than the normal 45 bytes. If the size is not a multiple of 3, this fact can be determined by the value of the count on
the last line. Extra dummy characters are included to make the character count a multiple of 4. The body is terminated by a line with a
count of zero. This line consists of one ASCII space.
The trailer line consists of "end" on a line by itself.
See Also
mail(1), uucp(1c), uudecode(1c), uuencode(1c), uusend(1c)
uuencode(5)