04-06-2009
The error is pretty obvious.
ce1 interface went down and came up. Could be a network fluctuation or a cable defect(in which case these messages are bound to repeat).
If you are repeatedly getting this,try changing the network cable. If it persists even after that,try changing the network port in the switch.
Thanks
HG
9 More Discussions You Might Find Interesting
1. Solaris
i have ce0 and ce1 online, on 2 different networks. im getting a message that says one nic is trying to assume the others IP or something to thta effect.
I do ifconfig -a and i see they have the same mac.
How do i deal with this?
Solaris 9 i beleive 04/04
Thanks,
Brian (2 Replies)
Discussion started by: BG_JrAdmin
2 Replies
2. Solaris
Dear ALL,
my server give me messages like below:
Apr 20 21:33:09 TAISERVER in.routed: interface bge3 to 192.168.11.22 turned off
I check with ifconfig,but nothing error that,how can make it solve...thanks for your help. (7 Replies)
Discussion started by: fredginting
7 Replies
3. Solaris
Hi there. My first time posting so apologies for any indescretions in advance. :o I've got two SunFire V440 servers running Solaris 5v10. Both have a quad Gigabit ethernet card fitted, both have the same symptom; that is, I can't get the first port ce1 to run Gigabit. Motherboard ports are ce0 and... (10 Replies)
Discussion started by: fixit9660
10 Replies
4. Solaris
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies
5. SCO
Hi all
I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface?
If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies
6. IP Networking
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
Discussion started by: mghis
3 Replies
7. UNIX for Dummies Questions & Answers
Hi All,
How to check whether a Interface has a single port or dual port.Thanks in advance. (5 Replies)
Discussion started by: rama krishna
5 Replies
8. UNIX for Dummies Questions & Answers
Just wanted to understand what is the logic being used by Solaris(kernel) to transmit data/traffic on physical interfaces.
I have seen most of the time traffic is being sent to interface ce0 and sometime to ce1.
I have removed ip address from below command for some reason.
netstat -rn
... (3 Replies)
Discussion started by: nadeemahmed
3 Replies
9. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT OPENSOLARIS
scconf_transp_adap_ge
scconf_transp_adap_ge(1M) System Administration Commands scconf_transp_adap_ge(1M)
NAME
scconf_transp_adap_ge - configure the Gigabit Ethernet (ge) transport adapter
DESCRIPTION
Note -
Beginning with the Sun Cluster 3.2 release, Sun Cluster software includes an object-oriented command set. Although Sun Cluster software
still supports the original command set, Sun Cluster procedural documentation uses only the object-oriented command set. For more infor-
mation about the object-oriented command set, see the Intro(1CL) man page.
You can configure ge adapters as cluster transport adapters. These adapters can only be used with transport type dlpi.
The ge adapter connects to a transport switch or to another ge adapter on a different node. In either case, the connection is made through
a transport cable.
When a transport switch is used and the endpoints of the transport cable are configured using scconf, scinstall, or other tools, you are
asked to specify a port name on the transport switch. You can provide any port name, or accept the default, as long as the name is unique
for the switch.
The default is to set the port name to the node ID hosting the adapter at the other end of the cable.
There are no user configurable properties for cluster transport adapters of this type.
SEE ALSO
clinterconnect(1CL), clnode(1CL), scconf(1M), scinstall(1M), ge(7D)
Sun Cluster 3.2 4 May 2006 scconf_transp_adap_ge(1M)