|
|
Sponsored Content
Special Forums
UNIX and Linux Applications
High Performance Computing
Veritas Cluster Server Management Console IP Failover
Post 302304221 by zxmaus on Sunday 5th of April 2009 08:06:15 PM
|
|
10 More Discussions You Might Find Interesting
1. High Performance Computing
Hello,
This might not be the right place to post my questions.
- I installed VCS 5.0 on the 2 nodes. What's next? I want to test the HA of NFS: i.e. the shared disk always accessible if one node goes down. How to do that?
- The management console was not installed. This is the GUI to manage... (2 Replies)
Discussion started by: melanie_pfefer
2 Replies
2. Solaris
Is it possible to configure veritas cluster server using 2 Ldoms on same host? I just want to test and learn VCS. We can do a cluster (sun cluster3.2 ) in a box using 2 Ldoms but i 'm not sure if thats possible with veritas cluster or not ? (1 Reply)
Discussion started by: fugitive
1 Replies
3. Solaris
Hi,
We have two sun SPARC server in Clustered (Sun Cluster 3.1). For some reason, System 1 failed over to System 2. Where can I find the logs which could tell me the reason for this failover?
Thanks (5 Replies)
Discussion started by: Mack1982
5 Replies
4. Solaris
Yesterday my customer told me to expect a vcs upgrade to happen in the future. He also plans to stop using HDS and move to EMC.
Am thinking how to migrate to sun cluster setup instead.
My plan as follows leave the existing vcs intact as a fallback plan.
Then install and build suncluster on... (5 Replies)
Discussion started by: sparcguy
5 Replies
5. Gentoo
How to failover the cluster ? GNU/Linux
By which command,
My Linux version
2008 x86_64 x86_64 x86_64 GNU/Linux
What are the prerequisites we need to take while failover ?
if any
Regards (3 Replies)
Discussion started by: sidharthmellam
3 Replies
6. UNIX for Advanced & Expert Users
Hello,
Usually I use "vxresize" to grow vxfs directory in a stand-alone server without any problems, but I am just told to grow vxfs directorys in Veritas Cluster nodes.
Since I never done it before, would like to ask all the experts here to make sure the concept and steps will be fine... (1 Reply)
Discussion started by: sunnychen98
1 Replies
7. Solaris
Hello experts -
I am planning to install a Sun cluster 4.0 zone cluster fail-over. few basic doubts.
(1) Where should i install the cluster s/w binaries ?. ( global zone or the container zone where i am planning to install the zone fail-over)
(2) Or should i perform the installation on... (0 Replies)
Discussion started by: NVA
0 Replies
8. Solaris
Until I really began to explore the practical implications of using ZFS with VCS, I would not have necessarily realised the obstacles that would be put in my path. Data integrity is a must-have for storage in a shared host environment, so it surprised me to learn as I opened this particular... (0 Replies)
Discussion started by: cambridge
0 Replies
9. Red Hat
Hi Guys,
I am not much aware of clusters but i have few questions can someone provide the overview as it would be very helpful for me.
How can i perform cluster failover test to see all the services are failing back to other node ? If it is using veritas cluster then what kind of... (2 Replies)
Discussion started by: munna529
2 Replies
10. UNIX for Beginners Questions & Answers
Hi Experts,
I wanted to extend a veritas file system which is running on veritas cluster and mounted on node2 system.
#hastatus -sum
-- System State Frozen
A node1 running 0
A node2 running 0
-- Group State
-- Group System Probed ... (1 Reply)
Discussion started by: Skmanojkum
1 Replies
LEARN ABOUT OPENSOLARIS
scprivipd
scprivipd(1M) System Administration Commands scprivipd(1M) NAME
scprivipd - Sun Cluster Private IP address service daemon SYNOPSIS
/usr/cluster/lib/sc/scprivipd DESCRIPTION
Sun Cluster private IP addresses can be assigned to non-global zones by using the scconf command or the clnode command. The scprivipd dae- mon is a server daemon that is used for the management of these private IP addresses that are assigned to non-global zones. The scprivipd daemon is started at system boot time. It is used to configure or unconfigure the private IP addresses that are assigned to non-global zones on zone boot or shutdown or as a result of scconf operations. DIAGNOSTICS
The scprivipd daemon has no direct stdin, stdout, or stderr connection to the outside. All diagnostic messages are logged through the sys- log function. NOTES
The scprivipd daemon must be run in superuser mode. The scprivipd daemon is a Service Management Facility (SMF) service and is started through SMF. Also, if the scprivipd daemon is killed by a signal, it is automatically restarted by SMF. The SIGTERM signal can be used to kill scprivipd gracefully. Other signals should not be used to kill the daemon. ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWscu | +-----------------------------+-----------------------------+ |Interface Stability |Private | +-----------------------------+-----------------------------+ SEE ALSO
clnode(1CL), scconf(1M), syslog(3C), attributes(5) Sun Cluster 3.2 19 May 2006 scprivipd(1M)