Sponsored Content
Full Discussion: Gigabit Link throughput
Special Forums IP Networking Gigabit Link throughput Post 302303415 by debd on Thursday 2nd of April 2009 02:43:25 PM
Old 04-02-2009
Gigabit Link throughput

As a rule of thumb in doing calculations, what figure would you use in Mbytes/sec? I know the answer varies grealty on the topolgy of the network but I wonde what newteok engineers use a rough rule of thumb?

Many thanks.
 

10 More Discussions You Might Find Interesting

1. Solaris

100 gigabit full duplex

How can I tell on Solaris 9 sparc if my nics are running 100 gigabit full duplex... (4 Replies)
Discussion started by: csaunders
4 Replies

2. UNIX for Advanced & Expert Users

how can i test my tape throughput in Mb/sec?

Is there a tool or cmd line program i can use to test my tape throughput in Mb/sec? thank you (2 Replies)
Discussion started by: progressdll
2 Replies

3. UNIX for Advanced & Expert Users

tool to monitor throughput

Was wonder if there was a tool or program I could run to measure throughput on our CentoS 4.x server. Our current dedicated host provider is charging us by how much throughput we are using and I just want to see if their numbers add up to whatever I get using a throughput tool of some kind. ... (6 Replies)
Discussion started by: mcraul
6 Replies

4. SCO

SCO6: Upgrading nd: no intel gigabit drivers?

I just (re)installed SCO6 here from scratch because I am hunting a problem. So, I installed it, then got the SCO OpenServer Release 6.0.0 Maintenance Pack 4 Device Drivers Supplement .iso and installed the nd package. # mount -F cdfs /dev/cd0 /cd-rom # pkgadd -d /cd-rom Then elect the nd... (2 Replies)
Discussion started by: dalek
2 Replies

5. IP Networking

How to improve throughput?

I have a 10Gbps network link connecting two machines A and B. I want to transfer 20GB data from A to B using TCP. With default setting, I can use 50% bandwidth. How to improve the throughput? Is there any way to make throughput as close to 10Gbps as possible? thanks~ :) (3 Replies)
Discussion started by: andrewust
3 Replies

6. Solaris

SUN GIGABIT ETHERNET CARD

Hi, we have SUN Gigabit ethernet cards at the server, both have 2 lines connected but hiw can I found out which cable is on which port before I configure it: the cards has 4 ports , from right to left the cables are connected at the first right then 2 empty then the last at the left side. ... (1 Reply)
Discussion started by: manni2
1 Replies

7. Solaris

Throughput problems with solaris aggregation

Hello gurus, I have the following configuration in the server side: # dladm show-aggr key: 33 (0x0021) policy: L4 address: 0:14:4f:6c:11:8 (auto) device address speed duplex link state nxge0 0:14:4f:6c:11:8 1000 Mbps ... (3 Replies)
Discussion started by: FERCA
3 Replies

8. IP Networking

Issue with ns2 - no throughput data

Hello, First time poster here hoping to get some help with ns2. I've recently started using ns2(first time user) but I'm having difficulty getting the results I'm after. I am trying to set up a network with wireless nodes(5-15 nodes) and then use xgraph to display a timing diagram,... (0 Replies)
Discussion started by: UnicksMan
0 Replies

9. IP Networking

OID for Bandwith and Throughput Measurement

Hey Guys, Does anybody know, which OID's of Net-SNMP is used to collect throughput and bandwith usage of machine?? I got these OID's ..iso.org.dod.internet.mgmt.mib-2.interfaces.ifTable.ifEntry.ifOutOctets ..1.3.6.1.2.1.2.2.1.16 ... (1 Reply)
Discussion started by: franzramadhan
1 Replies

10. UNIX for Advanced & Expert Users

Bonding IEEE 802.3ad Dynamic link aggregation : Bond showing less than desired throughput

Hi All, I have done IEEE 802.3ad Dynamic link aggregation bond configuration with name bond0 which has 4 slaves (each 25GB/s) in it on cent os 6.8. Issue i am facing is bonding throughput is only 50GB/s not 100GB/s. below are the configuration files : DEVICE=bond0 IPADDR=xx.xx.xx.xx... (1 Reply)
Discussion started by: omkar.jadhav
1 Replies
CSS::DOM::Rule(3pm)					User Contributed Perl Documentation				       CSS::DOM::Rule(3pm)

NAME
CSS::DOM::Rule - CSS rule class for CSS::DOM VERSION
Version 0.14 SYNOPSIS
use CSS::DOM::Rule ':all'; # import constants use CSS::DOM; $sheet = new CSS::DOM; $sheet->insertRule('bla blah blah {}'); $rule = $sheet->cssRules->[0]; $rule->type; # STYLE_RULE $rule->cssText; # 'bla blah blah {}' or similar $rule->cssText('p { margin: 0 }'); # replace it $rule->parentStyleSheet; # $sheet DESCRIPTION
This module provides the CSS rule class for CSS::DOM. It implements the CSSRule and CSSUnknownRule DOM interfaces. METHODS
Constructor Only call the constructor on this class to create an 'unknown' rule. You have to call the constructor on a particular subclass to get another type. Normally you do not need to call this directly anyway. (See CSS::DOM's "parse" and "insertRule" methods.) But just in case you do want to call it, here it is: new CSS::DOM::Rule $parent; # unknown rule require CSS::DOM::Rule::Style new CSS::DOM::Rule::Style $parent; # etc. $parent is the parent rule, if the rule is nested, or the parent style sheet otherwise. Object Methods type Returns one of the constants below indicating the type of rule. cssText Returns this rule's CSS code. If you pass an argument, it will be parsed as the new CSS code for this rule (replacing the existing data), and the old value will be returned. This method will die if the replacement CSS code creates a different type of rule. parentStyleSheet This returns the style sheet to which the rule belongs. parentRule This returns the rule's parent rule, if there is one, or an empty list otherwise. There is only a parent rule if this one is nested, e.g., inside a media rule. EXPORTS
The following constants that indicate the type of rule will be exported on request (individually or with the ':all' tag): UNKNOWN_RULE STYLE_RULE CHARSET_RULE IMPORT_RULE MEDIA_RULE FONT_FACE_RULE PAGE_RULE SEE ALSO
CSS::DOM CSS::DOM::Rule::Style CSS::DOM::Rule::Media CSS::DOM::Rule::Page CSS::DOM::Rule::Import perl v5.10.1 2010-12-10 CSS::DOM::Rule(3pm)
All times are GMT -4. The time now is 10:55 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy