Sponsored Content
Operating Systems AIX How to upgrade AIX TL (technology level) Post 302302878 by plechu on Wednesday 1st of April 2009 08:53:36 AM
Old 04-01-2009
It's good to update first bos.rte.install (smitty install -> Install and Update Software -> Install and Update from ALL Available Software). Then you can update the rest of filesets. During preview you will see all errors which can occur during update. If you just update TL (without separate update of bos.rte.install), preview will show you statement about bos.rte.install installation. Small think but can help.



P.S. after updating you will have to reboot server
 

10 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

Howto upgrade AIX to Level Update 4320-02_AIX_ML

Hi, Installing a new version of PROGRESS DB software 9.1c requires us to upgrade AIX to Level Update 4320-02_AIX_ML ( http://techweb.progress.com/kbase/19779 ) How would a do this savely. This is what i have already. 1) take a system backup. 2) find the level we are on right now. #... (1 Reply)
Discussion started by: progressdll
1 Replies

2. AIX

Technology Level update errors

Hello, I recently did an update from 5300-0-0 to 5300-05-06. When I run lppchk -v I get the following errors: # lppchk -v lppchk: The following filesets need to be installed or corrected to bring the system to a consistent state: invscout.rte 2.1.0.0 (not... (4 Replies)
Discussion started by: dkranes
4 Replies

3. AIX

AIX Technology Level 9

Hi Guys I am currently running AIX 5.3 technology level 6 on a 570, but want to go up to level 9. However I am struggling to find on IBM's website the new features that it brings in, along with the commands for these new features. Can any one help me with this? Thanks (7 Replies)
Discussion started by: ryanbsc@gmail.c
7 Replies

4. AIX

Update technology level

Hello I update one lpar from TL03 to TL06 reboot and check with lppchk -v, errpt and everything looks fine then I commit my fileset and I update to TL08-04. The installation was ok. I reboot my machine again check with lppchk -v and errpt and its ok, but when I type oslevel -s I get this... (5 Replies)
Discussion started by: lo-lp-kl
5 Replies

5. AIX

How to upgrade AIX Firmware & TL Maintenance Level in AIX

Steps to upgrade AIX TL ( technology Level ) / Maintenance Level in AIX ( including Firmware HMC VIOS ) This article or post covers upgrades for - Hardware Management Console ( HMC ) - Firmware ( also known as microcode ) - VIO ( Virtual I/O Server = PowerVM ) - AIX Version, Technology... (2 Replies)
Discussion started by: filosophizer
2 Replies

6. Solaris

Zone Servers Level Upgrade

Hi All, I am planning to do the Solaris level upgrade from "Solaris 10 1/06 s10s_u1wos_19a" to "Solaris 10 10/09 s10s_u8wos_08a" with 7 Non-global zones on it..... I have done Level upgrade for Solaris 10 boxes without Non-global zones..... Can any one let me know, whether it is possible... (8 Replies)
Discussion started by: indradev
8 Replies

7. AIX

rolling back Technology Level

Hi, is it possible to roll back currently updated Technology level ? what are steps required? Regards, Manoj (2 Replies)
Discussion started by: manoj.solaris
2 Replies

8. What is on Your Mind?

Which technology is better with UNIX/AIX

Hi Guys, need your help .... I am working in UNIX field from last 2 years, its my career starting days.. Which technology I have to melt up with NIX knowledge which can provide me high opportunities in today's IT market ?? Now a days, I am learning C. I m not want to hurt anyone but some says... (0 Replies)
Discussion started by: atul9806
0 Replies

9. AIX

AIX OS level

I currently have 2 servers running AIX 6.1 on them, but the OS level is listed differently in WSM. I am fairly new to AIX and just re-installed the OS on one of the boxes that originally had 5.1 on it. It now shows 6.1.0.0, whereas the other one shows 6.1.3.0. I have been trying to figure out how... (2 Replies)
Discussion started by: rifamilyguy
2 Replies

10. AIX

Pre-installation verification before technology level update

Hello, I was trying to upgrade TL on a lab server (test box). I did worked on (few) these type of SP and TL updates in the recent past. I saw the below message for the first time on server. current OS level : 7100-03-01-1341 downloaded the newest/recent fix pack from fix central as... (3 Replies)
Discussion started by: system.engineer
3 Replies
BOS_SETRESTRICTED(8)					       AFS Command Reference					      BOS_SETRESTRICTED(8)

NAME
bos_setrestricted - place a server in restricted mode SYNOPSIS
bos setrestricted -server <machine name> -mode 1 [-cell <cell name>] [-noauth] [-localauth] [-help] DESCRIPTION
The bos restricted command places the server in restricted mode. This mode increases the security of the bos server by removing access to a number of bos commands that are only used whilst configuring a system. When a server is in restricted mode, access to bos_exec, bos uninstall, bos install, bos create, bos install, bos delete, bos prune is denied, and the use of bos getlog is limited. CAUTIONS
Once a server has been placed in restricted mode, it may not be opened up again using a remote command. That is, bos setrestricted has no method of setting an unrestricted mode. Once a server is restricted, it can only be opened up again by sending it a SIGFPE, which must be done as root on the local machine. OPTIONS
-server <machine name> Indicates the server machine to restrict. -cell <cell name> Names the cell in which to run the command. Do not combine this argument with the -localauth flag. For more details, see bos(8). -noauth Assigns the unprivileged identity "anonymous" to the issuer. Do not combine this flag with the -localauth flag. For more details, see bos(8). -localauth Constructs a server ticket using a key from the local /etc/openafs/server/KeyFile file. The bos command interpreter presents the ticket to the BOS Server during mutual authentication. Do not combine this flag with the -cell or -noauth options. For more details, see bos(8). -help Prints the online help for this command. All other valid options are ignored. PRIVILEGE REQUIRED
The issuer must be listed in the /etc/openafs/server/UserList file on the machine named by the -server argument, or must be logged in as the local superuser "root" if the -localauth flag is included. As noted above, this command cannot be run against servers which are already in restricted mode. SEE ALSO
bos(8) COPYRIGHT
Copyright 2009 Simon Wilkinson <simon@sxw.org.uk> This documentation is covered by the BSD License as written in the doc/LICENSE file. This man page was written by Simon Wilkinson for OpenAFS. OpenAFS 2012-03-26 BOS_SETRESTRICTED(8)
All times are GMT -4. The time now is 04:17 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy