04-01-2009
Lots of people have done this.
The database software usually comes with backup commands.
10 More Discussions You Might Find Interesting
1. SCO
I am facing a problem to install sco 5.0.6 in Dell Power Edge SC1420 which raid controller is ultra 320 scsi raid controller .
how/from where to download the ultra 320 scsi raid controller driver for sco 5.0.6.
Plz help with any idea
karzon (1 Reply)
Discussion started by: karzon
1 Replies
2. SCO
recently we have purchased hp proliant ml350 g5 server and configured raid 5 with hp smartarray p200i sas controller.but i could not found any sas raid controller hp smartarry p200i driver for sco unix 5.0.7 :(.i searched on hp support site,but no use.any one can help. (3 Replies)
Discussion started by: prakrithi
3 Replies
3. Solaris
hi
this may be a very stupid question, but im quite new to Solaris (gonna buid my first system, Solaris 10 on x86 system, connected to other windows systems in a home network)
i wanna put a RAID 5 system in there to back up my other systems at home; iv read that its really so easy with SVM to... (4 Replies)
Discussion started by: Landser
4 Replies
4. Hardware
Hi,
We have a Sunfire 4150 with On-Board Internal Raid Controller connected to 4 X 146 GB SAS disks.
This also has an External Raid Controller (Storagetek Eight-Port, External HBA
Model SG-XPCIESAS-R-EXT-Z) connected to a JBOD array ( Storagetek XTA2530 ) which has 5 X 300 GB Hard disk.
... (1 Reply)
Discussion started by: ranjansukumar
1 Replies
5. Linux
I just built a home computer with 3TB hard drives I wanted to set up in a RAID 5 and load Ubuntu server onto it.
The first thing I did was set up the drives in a RAID 5 using just the motherboard chipset software to do it, so a 'hardware' RAID basically.
I installed Windows first to see if... (2 Replies)
Discussion started by: lorewap3
2 Replies
6. AIX
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies
7. AIX
Hello folks,
Could someone tell me why I unable to create pdisks for a RAID Array
# lscfg | grep scsi
+ sisscsia0 U787A.001.DPM0707-P1 PCI-X Dual Channel Ultra320 SCSI Adapter
+ scsi0 U787A.001.DPM0707-P1-T10 PCI-X Dual Channel Ultra320 SCSI Adapter... (12 Replies)
Discussion started by: filosophizer
12 Replies
8. Red Hat
Hello,
I want to delete a RAID configuration an old server has.
Since i haven't the chance to work with the specific raid controller in the past can you please help me how to perform the configuraiton?
I downloaded IBM ServeRAID Support CD but i wasn't able to configure the video card so i... (0 Replies)
Discussion started by: @dagio
0 Replies
9. Red Hat
Hello,
I am using Red Hat 2.6.23.1 with RAID 6 controller (card).
(When I use "cat /proc/partitions" I do not see the separate HDDs in the RAID, I see one drive for the RAID itself, as it is considered 1 large drive.)
I used a "dd" check to test my RAID drive speed and found it was a bit slow,... (7 Replies)
Discussion started by: Dbugy
7 Replies
10. SCO
Hi all,
A client has an SCO OpenServer Server 6.0, that is running on an HP ProLiant Box and they lost the root password.
Its equipped with a Doal-Core Intel Pentium Processor. They don't have any media or emergency disk anymore.
I tried to boot with the CD Rom, then "Tools", then exit to... (7 Replies)
Discussion started by: thm2222
7 Replies
LEARN ABOUT REDHAT
amrmtape
AMRMTAPE(8) System Manager's Manual AMRMTAPE(8)
NAME
amrmtape - remove a tape from the Amanda database
SYNOPSIS
amrmtape [ -n ] [ -v ] [ -q ] [ -d ] config label
DESCRIPTION
Amrmtape invalidates the contents of an existing backup tape in the configuration database. This is meant as a recovery mechanism when a
good backup is damaged either by faulty hardware or user error, e.g. the tape is eaten by the drive or is overwritten.
See the amanda(8) man page for more details about Amanda.
OPTIONS
-n Generate new tapelist and database files with label removed, but leave them in /tmp and do not update the original copies.
-v List backups of hosts and disks that are being discarded. Enabled by default.
-q Opposite of -v.
-d Run in debugging mode so all executed commands are shown.
EXAMPLE
Remove tape labeled DAILY034 from the DailySet1 configuration.
# amrmtape DailySet1 DAILY034
AUTHOR
Adrian T. Filipi-Martin <atf3r@cs.virginia.edu>
SEE ALSO
amadmin(8), amanda(8)
AMRMTAPE(8)