I have been looking in the scripts for interface management, in an effort to kick off a script of my own on any "significant network event" (I will qualify that in a bit)
I managed to add a check to tell netplugd to run my script every time there is a hot-plug event. Now I need to make it so my... (0 Replies)
hi there
the ethernet wire was out of the pc when the system started.
#ifconfig
#ifconfig -a
i did not get any ip for eth0.
i plug the cable into the pc
#ifdown eth0
#ifup eth0
now the ip address is assigned to eth0
Question is : IS this right way to bring ethernet down... (2 Replies)
I've been finding myself using a log file colorizer written in perl to reformat and colorize the output from many different programs. Mainly, however, I use it to make the output from "tail -f" commands more readable.
The base perl script I use is based on "colorlogs.pl" available from the... (1 Reply)
How can view log messages between two time frame from /var/log/message or any type of log files.
when logfiles are very big and especially many messages with in few minutes, I would like to display log messages between 5 minute interval.
Could you pls give me the command? (1 Reply)
AM in need of some plugin/script that can monitor HP-UX file "/var/opt/resmon/log/event.log" .
Have written a scrip in sh shell that is working fine for syslog.log and mail.log as having standard format, have interrogated that to Nagios and is working as I required .
But same script failed to... (3 Replies)
is there a way to efficiently monitor logfiles that do not have a date or time format? i have several logs on several different servers that need to be monitored. but i realized writing a script for this would be very complex and time consuming giving the variety of things i need to check for i.e.... (2 Replies)
I've got an issue with a VMWare server running RHEL 6.3 that has dual E1000 NICs. I have configured the cards as I would normally do in /etc/sysconfig/network-scripts as ifcfg-eth0 and ifcfg-eth1. I can execute ifup eth0 and bring the interface up quite happily, however when I execute ifup eth1 it... (2 Replies)
How to check log size every 10min. by script (can use crontab)
if log size not change with alert "Log not update"
Base run on SunOS 5.8 Generic_Virtual sun4u sparc SUNW,SPARC-Enterprise
logFiles="log1.log log2.log"
logLocation="/usr/home/test/log/"
Out put.
Tue Jan 31... (3 Replies)
Hi ,
We have around 22 logs , each has different entries. I have to automate this using shell script. The ideas which am sharing is given below
1) We use only TAIL -100 <location and name of the log> Command to check the logs.
2) We want to check whether the log was updated before 24... (13 Replies)
Below is my script to log all the command input by any user to /var/log/messages. But I cant achieve the desired output that i want. PLease see below.
function log2syslog
{
declare COMMAND
COMMAND=$(fc -ln -0)
logger -p local1.notice -t bash -i -- "$USER:$COMMAND"
}
trap... (12 Replies)
Discussion started by: invinzin21
12 Replies
LEARN ABOUT SUSE
ifservices
IFSERVICES(5) Network configuration IFSERVICES(5)NAME
ifservices-* - control network services with ifup/down
SYNOPSIS
/etc/sysconfig/network/ifservices-<configuration_name>/
DESCRIPTION
The directory /etc/sysconfig/network/ifservices-<configuration_name>/ is read by the script /etc/sysconfig/network/scripts/ifup-services
which starts and stops system services when an interface is set up/down. ifup-services is used by /sbin/ifup, which is the command line
user interface for setting up network interfaces.
This is useful if you don't have a permanent network connection. If you sometimes boot without network and plug in the network cable later
you can add links to system services in this directory. These services will then be started with ifup and stopped with ifdown.
The configuration name used for ifservices-* should match exactly the configuration name of the ifcfg-* file for the interface.
For the usage with NetworkManager (where you don't necessarily need a ifcfg-* file) you can also use /etc/sysconfig/network/ifser-
vices-<interface>-<essid>/ (for wlan interfaces) or if that does not exist /etc/sysconfig/network/ifservices-<interface>/. As a final
fallback /etc/sysconfig/network/ifservices/ is checked as well. If NetworkManager is active services will be stopped after the interface is
down.
The links in this directory are equal to the links in the runlevel directories /etc/init.d/rc*.d/ They have to point to service start
scripts which are usually in /etc/init.d/. Links starting with 'S' are start links, which are called in alphabetical order after ifup has
set up the interface. Links starting with 'K' are kill links which are called before ifdown takes down the interface. See also section
Sequencing Directories in boot (7).
EXAMPLE
In this example we use an interface with MAC address 00:de:ad:be:af:00. This interface is not always physically connected. As soon as you
plug in the cable ypbind and autofs should be started. When you pull the cable they should be stopped. This can be reached with:
in file /etc/sysconfig/network/ifcfg-eth-id-00:de:ad:be:af:00
...
STARTMODE=ifplugd
...
in dir /etc/sysconfig/network/ifservices-eth-id-00:de:ad:be:af:00/
S10portmap -> /etc/init.d/portmap
S20ypbind -> /etc/init.d/ypbind
S30autofs -> /etc/init.d/autofs
S20autofs -> /etc/init.d/autofs
K30ypbind -> /etc/init.d/ypbind
Now you have to disable the start of this services at boot time
chkconfig ypbind off
chkconfig autofs off
Notes:
You may call scripts/create-ifservices-directory [<interface_name>] to create a directory with the links from this example. This will cre-
ate the directory ifservices-<interface_name> or if no interface name was given ifservices-template.
Maybe you have to add also variable IFPLUGD_PRIORITY. For details about startmode ifplugd read ifup (8).
The service portmap had to be added because ypbind needs it. This service is still started at boot time because it does not need an active
network connection. But ypbind may now be started earlier as usual. Therefore we make sure that portmap is started before. Starting an
already running service again does not affect the service.
SEE ALSO ifup(8), ifcfg(5).
AUTHOR
Christian Zoz <zoz@suse.de>
sysconfig February 2005 IFSERVICES(5)