03-20-2009
Is this a brand new USB drive?
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi...
question is this:
How do I mount an LVD hotswap scsi drive in bay #2 on a netra using the mount command? volmgt doesn't seem to mount it and/or I don't know how to view the drives data if it's formatted which it may not be. This drive is not new out of the box so I'm not sure.
... (4 Replies)
Discussion started by: soulshaker
4 Replies
2. UNIX for Dummies Questions & Answers
I am using Redhat 9 Linux, and am trying to get my external usb drive mounted (fat32). If I look at the KDE Control panel, it lists a usb 2.0 storage device under "USB Devices" (also in /proc/bus/usb), and under "SCSI" as scsi1. I looked at /proc/scsi/usb-storage-0, and it lists it there also. What... (6 Replies)
Discussion started by: jeremiebarber
6 Replies
3. Solaris
Hello !
What is the comand to mount and usb hard disk ?
I have Solaris 10 installed!
10nx! (1 Reply)
Discussion started by: daniel.balasa
1 Replies
4. AIX
Dear All
Last day in Aix 5.2 server by executing
# df –g
I found following:
Filesystem GB blocks Free %Used Iused %Iused Mounted on
.
.
/dev/fslv00 58.00 136.70 -135% 212103 1% /sprod
After shutting down by following command
# shutdown –h
And when... (1 Reply)
Discussion started by: xa52000
1 Replies
5. SCO
Can anybody help me out to mount USB flash /floppy drive in sco openserver 6.0 . (5 Replies)
Discussion started by: sureshdrajan
5 Replies
6. UNIX for Dummies Questions & Answers
Hi!
I have a problem with my disk, it is full as you can see
# df
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/sda1 64380356 63125180 0 100% /
none 3116000 0 3116000 0% /dev/shm
/dev/sdb1 282015652... (10 Replies)
Discussion started by: ruisof
10 Replies
7. Solaris
Hello Gurus!!
Very recently i tried to mount a USB pen drive onto my solaris 10 (X4170 model) server. As i understand, in ideal scenarios it should get mounted automatically, but it did not happen. Neither anything is shown in "iostat -En" output or "rmformat -l" about the pen drive.
I also... (10 Replies)
Discussion started by: EmbedUX
10 Replies
8. Solaris
Hiii,
Please let me know the steps for mounting my USB pendrive in solaris 10 platform.
Thanks & Regards,
Bhargav P (5 Replies)
Discussion started by: bhargav90
5 Replies
9. Solaris
Hi,
I am facing issue with one of the drive is solaris 10. it is showing offline in the messages file
scsi: WARNING: /pci@2,600000/QLGC,qlc@0/fp@0,0/ssd@w5006016746e00b1b,0 (ssd0):
drive offline
genunix: WARNING: Page83 data not standards compliant DGC LUNZ 0430
... (1 Reply)
Discussion started by: Prasanth T K
1 Replies
10. Solaris
I have a Sun-Fire V440 running with Solaris 9 and am trying to get a WD USB Hard Drive mounted. None of the articles I've read so far have helped.
Output from rmformat:
Looking for devices...
1. Volmgt Node: /vol/dev/aliases/rmdisk0
Logical Node: /dev/rdsk/c5t0d0s2
... (17 Replies)
Discussion started by: oldtimertj
17 Replies
LEARN ABOUT FREEBSD
usb_template
USB_TEMPLATE(4) BSD Kernel Interfaces Manual USB_TEMPLATE(4)
NAME
usb_template -- USB templates
SYNOPSIS
To compile this module into the kernel, place the following line in your kernel configuration file:
device usb_template
To load the module at boot time, place the following line in loader.conf(5):
usb_template_load="YES"
DESCRIPTION
The usb_template module implements various USB templates that are needed when programming an USB device side driver. A USB template consists
of an USB device descriptor, one or more USB configuration descriptors, one or more USB interface descriptors, one or more USB endpoint
descriptors, USB strings and additional USB descriptors. The USB template module currently has templates for USB Mass Storage, USB CDC Eth-
ernet and Message Transfer Protocol. USB templates are currently selected using the "hw.usb.template" sysctl. The "hw.usb.template" value
can be changed at any time, but will not have any effect until the USB device has been re-enumerated.
SEE ALSO
usb(4)
STANDARDS
The usb_template module complies to the USB 1.0, 2.0 and 3.0 standard.
HISTORY
The usb_template module was written by Hans Petter Selasky <hselasky@FreeBSD.org>.
BSD
March 18, 2014 BSD