03-19-2009
Cant' mount usb drive, /dev/sda1 not showing up
Hi, I'm trying to mount a usb drive but the path /dev/sda1 does not show up under /dev when I plug in the usb device.
In fact I see no differences under /dev before and after I plugin my usb drive.
Any ideas why the system is not recognizing the usb drive and how to fix?
This is on a Solaris 10 OS.
thanks,
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi...
question is this:
How do I mount an LVD hotswap scsi drive in bay #2 on a netra using the mount command? volmgt doesn't seem to mount it and/or I don't know how to view the drives data if it's formatted which it may not be. This drive is not new out of the box so I'm not sure.
... (4 Replies)
Discussion started by: soulshaker
4 Replies
2. UNIX for Dummies Questions & Answers
I am using Redhat 9 Linux, and am trying to get my external usb drive mounted (fat32). If I look at the KDE Control panel, it lists a usb 2.0 storage device under "USB Devices" (also in /proc/bus/usb), and under "SCSI" as scsi1. I looked at /proc/scsi/usb-storage-0, and it lists it there also. What... (6 Replies)
Discussion started by: jeremiebarber
6 Replies
3. Solaris
Hello !
What is the comand to mount and usb hard disk ?
I have Solaris 10 installed!
10nx! (1 Reply)
Discussion started by: daniel.balasa
1 Replies
4. AIX
Dear All
Last day in Aix 5.2 server by executing
# df –g
I found following:
Filesystem GB blocks Free %Used Iused %Iused Mounted on
.
.
/dev/fslv00 58.00 136.70 -135% 212103 1% /sprod
After shutting down by following command
# shutdown –h
And when... (1 Reply)
Discussion started by: xa52000
1 Replies
5. SCO
Can anybody help me out to mount USB flash /floppy drive in sco openserver 6.0 . (5 Replies)
Discussion started by: sureshdrajan
5 Replies
6. UNIX for Dummies Questions & Answers
Hi!
I have a problem with my disk, it is full as you can see
# df
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/sda1 64380356 63125180 0 100% /
none 3116000 0 3116000 0% /dev/shm
/dev/sdb1 282015652... (10 Replies)
Discussion started by: ruisof
10 Replies
7. Solaris
Hello Gurus!!
Very recently i tried to mount a USB pen drive onto my solaris 10 (X4170 model) server. As i understand, in ideal scenarios it should get mounted automatically, but it did not happen. Neither anything is shown in "iostat -En" output or "rmformat -l" about the pen drive.
I also... (10 Replies)
Discussion started by: EmbedUX
10 Replies
8. Solaris
Hiii,
Please let me know the steps for mounting my USB pendrive in solaris 10 platform.
Thanks & Regards,
Bhargav P (5 Replies)
Discussion started by: bhargav90
5 Replies
9. Solaris
Hi,
I am facing issue with one of the drive is solaris 10. it is showing offline in the messages file
scsi: WARNING: /pci@2,600000/QLGC,qlc@0/fp@0,0/ssd@w5006016746e00b1b,0 (ssd0):
drive offline
genunix: WARNING: Page83 data not standards compliant DGC LUNZ 0430
... (1 Reply)
Discussion started by: Prasanth T K
1 Replies
10. Solaris
I have a Sun-Fire V440 running with Solaris 9 and am trying to get a WD USB Hard Drive mounted. None of the articles I've read so far have helped.
Output from rmformat:
Looking for devices...
1. Volmgt Node: /vol/dev/aliases/rmdisk0
Logical Node: /dev/rdsk/c5t0d0s2
... (17 Replies)
Discussion started by: oldtimertj
17 Replies
LEARN ABOUT DEBIAN
fpga_load
FPGA_LOAD(8) FPGA_LOAD(8)
NAME
fpga_load - Xorcom Astribank (xpp) firmware tool
SYNOPSIS
fpga_load [-g] [-r] [-v] -D {/proc/bus/usb|/dev/bus/usb}/BUS/DEV
fpga_load [-g] [-v] -D {/proc/bus/usb|/dev/bus/usb}/BUS/DEV -I firmware.hex [-b dump.bin] [-i]
fpga_load -h
DESCRIPTION
fpga_load loads the FPGA firmware to the Xorcom Astribank device. The syntax resembles that of fxload(8).
OPTIONS
-b dump.bin
Before writing firmware, bump the processed binary file to dump.bin.
-D DEVICE
Required. The device to read from/write to. On modern UDEV-based system this is usually /dev/bus/usb/bus_num/device_num, where
bus_num and device_num are the first two numbers in the output of lsusb(8). On older systems that use usbfs, it is usually
/proc/bus/usb/bus_num/device_num.
-r
Reset the Astribank and renumerate its USB connection to power on product ID.
-g
Dump all eeprom data to standard output.
-I fireware_file
The firmware file to write to the device.
-i
Show information about the firmware file (valid only with -I option). Example:
./FPGA_1151.hex: Version=3297 Checksum=58270
In particular, the calculated checksum should match the output of sum(1) on the binary firmware file generated by the -b option.
-v
Increase verbosity. May be used multiple times.
-h
Displays usage message.
SEE ALSO
fxload(8), lsusb(8)
AUTHOR
This manual page was written by Tzafrir Cohen <tzafrir.cohen@xorcom.com> . Permission is granted to copy, distribute and/or modify this
document under the terms of the GNU General Public License, Version 2 any later version published by the Free Software Foundation.
On Debian systems, the complete text of the GNU General Public License can be found in /usr/share/common-licenses/GPL.
16 April 2006 FPGA_LOAD(8)