03-05-2009
Have you tried using fdisk to make it seen under UNIX first? Then format and devfsadm should see the disks as you expect.
10 More Discussions You Might Find Interesting
1. Solaris
hi after installation of sol 10 u 2 system started rebooting and when i tried to install solaris the system is giving:
panic/thread=cbacf800: BAD TRAP: type=e(#pf page fault) rp=fec38ae4 addr=458b247d occured in module "unix" due to an illegal access to a user address syncing file systems..... (2 Replies)
Discussion started by: nibiru78
2 Replies
2. Shell Programming and Scripting
Hello, the ls -d command to only list directories in a directory doesn't seem to work on Solaris and the man command says to use that combination: ls -d
Anyone have the same problem and find a resolve?
Thanks
BobK (9 Replies)
Discussion started by: bobk544
9 Replies
3. Solaris
I have a solaris 10 system configured using NetApp as its storage, and the file systems are already configured as you can see from the example below:
root@moneta # df -h
Filesystem size used avail capacity Mounted on
/dev/md/dsk/d0 9.8G 513M 9.3G 6% /
... (0 Replies)
Discussion started by: fretagi
0 Replies
4. Solaris
I have a solaris 10 system configured using NetApp as its storage, and the file systems are already configured as you can see from the example below:
root@moneta # df -h
Filesystem size used avail capacity Mounted on
/dev/md/dsk/d0 9.8G 513M 9.3G 6% /... (4 Replies)
Discussion started by: fretagi
4 Replies
5. UNIX for Dummies Questions & Answers
i'm trying to add disk to red hat , use fdisk -l but it doesn't recognize it
what should i do it to get it works? (3 Replies)
Discussion started by: prpkrk
3 Replies
6. Solaris
Good day.
I have a SUN Netra X4200 running on Solaris 10, with two disks in raid 1 configuration. HDD0 (c2t0d0) seems to have a problem but HDD1 (c2t1d0) is ok:
# for a in c2t0d0 c2t1d0 ; do raidctl -l $a; done
Volume Size Stripe Status Cache RAID
Sub ... (5 Replies)
Discussion started by: BRH
5 Replies
7. Solaris
Hi, one of my server won't boot. I restarted system while sysconfig configure was running. I can't boot into normal user mode. I always get error svc:/system/config-user:default is in maintenance mode and some lib exists with status 95.
I tried to boot into single user mode and to clear this... (6 Replies)
Discussion started by: solaris_user
6 Replies
8. Hardware
Hello,
I have a spare SUN server X4200 with a DC PSU (oracle part number 300-2186)
The PSU is the one in the photo
I was looking in the net about what cable i can order but i couldn't find anything that fit there :)
Any idea?
Thanks! (2 Replies)
Discussion started by: @dagio
2 Replies
9. UNIX for Advanced & Expert Users
Hello,
I have rebooted the RHEL VM but after rebooting the vm it not showing all the partition mounted on OS level, if i'll execute the fdisk -l command, then i'm able to see the same disk. below is the fdisk output :
# fdisk -l
Disk /dev/sda: 107.6 GB, 107639996416 bytes
255 heads, 63... (1 Reply)
Discussion started by: purushottamaher
1 Replies
10. Solaris
Hi Guys,
Could someone please share the dvd/cd that came with server Netra x4200 M2 since it is not more available in Oracle site? Or do you know where I can get that?
Thanks! (4 Replies)
Discussion started by: CristianS
4 Replies
LEARN ABOUT CENTOS
diskscan
diskscan(1M) System Administration Commands diskscan(1M)
NAME
diskscan - perform surface analysis
SYNOPSIS
diskscan [-W] [-n] [-y] raw_device
DESCRIPTION
diskscan is used by the system administrator to perform surface analysis on a portion of a hard disk. The disk portion may be a raw parti-
tion or slice; it is identified using its raw device name. By default, the specified portion of the disk is read (non-destructive) and
errors reported on standard error. In addition, a progress report is printed on standard out. The list of bad blocks should be saved in a
file and later fed into addbadsec(1M), which will remap them.
OPTIONS
The following options are supported:
-n Causes diskscan to suppress linefeeds when printing progress information on standard out.
-W Causes diskscan to perform write and read surface analysis. This type of surface analysis is destructive and should be invoked
with caution.
-y Causes diskscan to suppress the warning regarding destruction of existing data that is issued when -W is used.
OPERANDS
The following operands are supported:
raw_device The address of the disk drive (see FILES).
FILES
The raw device should be /dev/rdsk/c?[t?]d?[ps]?. See disks(1M) for an explanation of SCSI and IDE device naming conventions.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Architecture |x86 |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
SEE ALSO
addbadsec(1M), disks(1M), fdisk(1M), fmthard(1M), format(1M), attributes(5)
NOTES
The format(1M) utility is available to format, label, analyze, and repair SCSI disks. This utility is included with the diskscan, addbad-
sec(1M), fdisk(1M), and fmthard(1M) commands available for x86. To format an IDE disk, use the DOS format utility; however, to label, ana-
lyze, or repair IDE disks on x86 systems, use the Solaris format(1M) utility.
SunOS 5.10 24 Feb 1998 diskscan(1M)