Hi,
I have a problem with a server disconnecting from the network.
This is a SUN box with dual NIC's running Solaris 8.
We have a Nokia router that routes traffic but it's virtual address doesn't respond to pings. When the SUN box sends out a ping, if nothing comes back it will shut down... (5 Replies)
I have one 4GB, dual port HBA. Is each port rated for 4GB, or is it the whole HBA rated for 4GB?
Also, how do I determine which is port0 / port1 with "lscfg -vl fcs0" command. Thanks. (0 Replies)
Greetings Forumers!
I am running into an issue with multiple zones on an M5000 with 2 NICs. The NICs are on separate VLANs. These zones are using the 2 NICs to communicate with other systems but when they need to communicate with a zone on the same system, but different NIC, the application... (9 Replies)
All
I am at a loss with a VIO server running ios 2.2.0.10-FP-24 SP-01. The VIO server is fitted with two 8Gb PCI Express Dual Port FC Adapters. However when I run the lsnports command only two of the adapter ports show as capable:
$ lsnports
name physloc ... (4 Replies)
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
Hi,
From the man page, cfgmgr configures devices and optionally installs device software by running the programs specified in the Configuration Rules object class and it is not dependent on platform .
Are there any fundamental differences impacting the speed of cfgmgr on a stand-alone and... (5 Replies)
NIC port is down on IBM Frame. From the back its slot C7/C8. The network switch is the problem, and a new switch will be coming into play. There's one VIO and one LPAR.
How do i tell the port is down in the OS on the VIO? And how can i verify it's backup without pulling cables? We have a... (1 Reply)
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
LEARN ABOUT OSF1
cfgmgr.auth
cfgmgr.auth(4) Kernel Interfaces Manual cfgmgr.auth(4)NAME
cfgmgr.auth - Configuration management server authorization database
SYNOPSIS
/etc/cfgmgr.auth
DESCRIPTION
The cfgmgr.auth file lists the remote systems that are authorized to modify the local system's kernel subsystem configuration. Using the
sysconfig command, system administrators can maintain the kernel subsystem configuration on local and remote hosts. To secure access to
the kernel subsystem configuration, the local configuration management server (cfgmgr) answers requests from remote systems only when the
remote system is listed in the cfgmgr.auth file.
Each entry in the file has the following form:
host-name
Where host-name specifies the full domain name of the remote host. You must list each remote host on a separate line and only the first
128 characters of each line are read and processed. Lines beginning with the pound sign (#) are comments.
If the cfgmgr.auth file does not exist, the configuration management server assumes no remote system administrators are allowed to config-
ure, reconfigure, or unconfigure any kernel subsystem on the local host.
EXAMPLES
The following shows entries in the cfgmgr.auth file on a host named buster:
salmon.zk3.dec.com
trout.zk3.dec.com
bluefish.zk3.dec.com
This cfgmgr.auth file allows system administrators on the salmon, trout, and bluefish hosts to configure, reconfigure, and unconfigure sub-
systems on buster.
RELATED INFORMATION
Commands: cfgmgr(8), sysconfig(8), sysconfigdb(8), kloadsrv(8)
Files: /etc/sysconfigtab(4)
System Administration delim off
cfgmgr.auth(4)