03-03-2009
You are more than likely using IPv4 not v6 so that should not be an issue. Do you have "connect at boot" selected in YaST? in /etc/sysconfig/network/, do you have any files with "eth" in them? Can you list them?
something like this would be needed:
DEVICE=eth0
ONBOOT=yes
BOOTPROTO=dhcp
Last edited by mark54g; 03-03-2009 at 02:37 PM..
10 More Discussions You Might Find Interesting
1. IP Networking
I have installed Solaris 8.0 and want to find out how can I go in and change my network setup and external IP setup. At the moment system running but I can not connect to the internet. But my lan card shows that I am on the network. I also get some advice that I should check the $Socks but how do I... (1 Reply)
Discussion started by: Cdrive
1 Replies
2. UNIX for Dummies Questions & Answers
Im on XP now but when im on linux how do I connect to the internet?
I don't think AOL works with it but are there any free programs that I can use with it? (8 Replies)
Discussion started by: NoPepsiForYou
8 Replies
3. UNIX for Dummies Questions & Answers
Hi all,
Is it possible (as I only have dial-up) to utilise my existing WinXP PC as a gateway to the internet for my 2nd PC (RH 8.0)?? .So connect with XP and have RH use a network connection (I guess) through the XP box and to the internet.
If so, could I please have some links thrown my... (1 Reply)
Discussion started by: Cameron
1 Replies
4. UNIX for Dummies Questions & Answers
I am using solaris 10 with pentium 3. I have two network cards but none of them come up when i run <ifconfig -a> in command line. The two cards I have are : Linksys LNE 100TX and Netgear FA311. Does solaris 10 support these NICs or do I have to dowload the drivers for them.
If so, can anyone... (1 Reply)
Discussion started by: fidjouss
1 Replies
5. Linux
Hi,
I can ping www.yahoo.com (then domain name server is OK) but I can not navigate by Motzila to www.yahoo.com or any other Web Site.
What can be the problem ? Mozila is configured in preference /advance to go automaticaly on WEB.
We are under RED HAT AS3.
What should I check ?
Many thanks... (1 Reply)
Discussion started by: big123456
1 Replies
6. UNIX for Dummies Questions & Answers
I have just installed Linux and everything looks great, but how do I get my browser (Mozilla) to connect to my internet service provider?
I have a cable connection to Bigpond in Australia, if that means anything - the ISP will not provide support for Linux.
Your help would be greatly... (2 Replies)
Discussion started by: openhead
2 Replies
7. Solaris
hi there, hope your chakras are all doing well :-)
just installed solaris 10 on my laptop, all seems fine except the internet. How can i connect on a DSL line?. spent 7 days and 3 nights trying but couldnt find the starting point....
alikun (22 Replies)
Discussion started by: alikun
22 Replies
8. UNIX for Advanced & Expert Users
Hi Guys,
I have trouble connecting to ftp server. My task is to connect to the proxy server and get the latest file to the local machine. It works fine when i do the same steps manually. I've been trying to do it in multiple ways but im just not able to connect. When i check the log, this is what... (4 Replies)
Discussion started by: stunnerz_84
4 Replies
9. SCO
Hi, I have a router, 192.168.1.1, and an internet router, 10.0.0.138. I have connected the server to the 1st router and assigned it a IP address of 192.168.1.1. I can ping both routers successfully but I have no access to internet. Any suggestions? sco5.0.7 (11 Replies)
Discussion started by: juan.navarrete
11 Replies
10. Ubuntu
Note: I originally posted this question on unix.stackexchange.com. But as my question was down-voted within an hour of asking, I came to the conclusion that perhaps I need to quit attempting to get help on StackExchange or that my inquiry is simply moronic. If anyone feels that my question is not... (7 Replies)
Discussion started by: AntumDeluge
7 Replies
LEARN ABOUT SUSE
ifndp-proxy
IFNDP-PROXY(5) Network configuration IFNDP-PROXY(5)
NAME
ifndp-proxy[-<interface name>] - IPv6 NDP and IPv4 ARP proxy entries
SYNOPSIS
/etc/sysconfig/network/ifndp-proxy
/etc/sysconfig/network/ifndp-proxy-<interface name>
DESCRIPTION
These files contain IPv6 NDP and IPv4 ARP proxy settings, that should be applied using the ip neigh add proxy command documented in the
ip(8) manual page that provides a common interface for IPv4 and IPv6.
The NDP/ARP proxy is required, e.g. when IP addresses from the same subnet have to be used on the interface of the host as well as on
interfaces behind a (tunnel) interface and using a bridge is not an option.
Don't forget to enable forwarding and the NDP/ARP proxy by setting
net.ipv6.conf.<all|default|interface name>.proxy_ndp = 1
net.ipv6.conf.<all|default|interface name>.forwarding = 1
and/or
net.ipv4.conf.<all|default|interface name>.proxy_arp = 1
net.ipv4.conf.<all|default|interface name>.forwarding = 1
or
net.ipv4.ip_forward = 1
either as global all setting in the /etc/sysctl.conf file or using the ifsysctl(5) files, that allow per-interface setup.
Forwarding can be also enabled in the /etc/sysconfig/sysctl file using the IP_FORWARD and IPV6_FORWARD variables.
The proxy entries are added and deleted using the if-{up|down}.d/ndp-proxy script, every time after an involved interface has been set
up or down.
SYNTAX
The format of the ifndp-proxy file is:
<address> <address interface> <proxy interface list>
The format of the ifndp-proxy-<address interface> file is same to above, but allows also to omit the address interface by using a "-" as
placeholder inside of the file, because it is already available in the file name:
<address> <address interface | -> <proxy interface list>
Lines beginning with # and blank lines are ignored.
Each line defines to add a proxy NDP/ARP entry with the address of or behind address interface to all interfaces in the proxy interface
list.
EXAMPLES
Let's assume, your machine is connected via eth0 to a switch with the networks 2001:db8:abba::/64 and 192.168.100.1/24 and is using the IP
address 1 itself. You'd like to use the addresses 11 and 12 e.g. for virtual machines behind the tap1 and tap2 interface, that is:
2001:db8:abba::1/64 -- local eth0 address
2001:db8:abba::11/64 -- address behind tap1
2001:db8:abba::12/64 -- address behind tap2
192.168.100.1/24 -- local eth0 address
192.168.100.11/24 -- address behind tap1
192.168.100.12/24 -- address behind tap2
then set up the following entries in the ifndp-proxy file:
2001:db8:abba::1 eth0 tap1 tap2
2001:db8:abba::11 tap1 eth0 tap2
2001:db8:abba::12 tap2 eth0 tap1
192.168.100.1 eth0 tap1 tap2
192.168.100.11 tap1 eth0 tap2
192.168.100.12 tap2 eth0 tap1
additionally to the routing entries in the routes or ifroute-<interface name> files.
BUGS
Please report bugs at <https://bugzilla.novell.com/>
AUTHOR
Marius Tomaschewski <mt@suse.de>
SEE ALSO
ifup(8) ifcfg(5) ifsysctl(8)
sysconfig December 2009 IFNDP-PROXY(5)