Reg. NIC card Post: 302292026

10 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

No NIC Card?

Hello Everyone, While trying to configure my network interface card on my system which runs mandrake 7, I have faced many problems. I used commands like netconf, drakconf, ifconfig etc to configure my NIC but of no use. There is no output for dmesg|grep eth. Does that mean that mandrake...

2. HP-UX

configuring nic card

using sam i have tryed to configure the nic, however when i try to do so i get an error saying i couldn't as i was using BIND ?

3. Linux

Howto Detect New Nic Card

Hi PPL! I have P-IV processor, with on-board NIC card. I have added one more NIC card for domestic use. My kudzu does not recognise the newly added PCMCIA NIC card. How to go about this one? Suggest PEnguin

4. HP-UX

how can I determine which NIC card is virtual NIC Card

how can I determine which NIC card is virtual NIC Card which condition can make a decision Does HP UX have Virtual Network Adapter Concept if ,it has where I can Find if I Install Virutal Network Adapter or which command that i can get it or which software can generate thanks

5. Solaris

Reg- eth0,eth1 (ethernet card)

Hi Guys, I am working as a L-1 support and i want to know that are the precaution need to take on eth0(Ethernet card) i heard on production server it is very much important, what are the steps need to observe on this tickets.

6. Solaris

NIC card repetative Failover

I have configure 2 NIC in ipmp group1 .Similarly other 2 NIC in ipmp group2 When I connect both NIC to 2 different switch , which is connect to one L3 switch as trunk. Both the NIC failover to each other continously. Following are the message log. ifmsdb1 in.mpathd: NIC failure detected...

7. Linux

changing speed of NIC Card in linux

Hi, I would like to know how to change the speed of ethernet card in linux? as it is showing auto-neg using mii-tool -v eth0 and my requirement is 100mbps full duplex. Regards, Manoj

8. Linux

How to check which NIC Card is used for backups?

I have a linux box with 2 nic cards on it one for prod and one for backup. My question is while the backup are happening how do I determine which nic is used for backups . I would like to run a command so that that I can see the usage in a dynamic fashion.

9. HP-UX

NIC card issue

Hi, Someone asked me the below. If the box has multiple NIC cards, try to run a test with interface address specified as shown below $ java utils.MulticastTest -N server100 -A 237.155.155.1 -i <interfaceaddress> How can I now find out if my box has multiple NIC cards and how can I...

10. Red Hat

Finding speed of NIC Card

Hi, I would like to know how to find out ACTUAL speed of NIC Card. I have used the command ethtool eth0, it is showing supported modes, but what is acutal speed ? how to find out?

LEARN ABOUT DEBIAN

vmblock

VMBLOCK(9)							   Open VM Tools							VMBLOCK(9)

NAME

       vmblock - vmware kernel module

SYNOPSIS

       modprobe vmblock

DESCRIPTION

       This  is a kernel filesystem module. Ideally, it should be loaded before any of the Tools userlevel components are allowed to start, though
       vmblock itself has no dependencies. When loaded, vmblock will establish itself in /proc/fs/vmblock and create two nodes	therein,  dev  and
       mountPoint. Before mounting a vmblock filesystem, ensure that /tmp/VMwareDnD exists as a directory with permissions 1777, otherwise host to
       guest drag n' drop operations won't work.

       To mount, issue:

	    mount -t vmblock none /proc/fs/vmblock/mountPoint

       Once mounted, vmware-user(1) can begin to make use of vmblock to assist with DnD operations. Note that  while  vmware-user(1)  is  running,
       it'll  keep  an	open  file  descriptor on /proc/fs/vmblock/dev, and thus all vmware-user(1) instances must be killed to unmount and unload
       vmblock.

OPTIONS

       vmblock has no options.

SEE ALSO

       vmware-checkvm(1)
       vmware-hgfsclient(1)
       vmware-toolbox(1)
       vmware-toolbox-cmd(1)
       vmware-user(1)
       vmware-xferlogs(1)
       libguestlib(3)
       libvmtools(3)
       vmware-guestd(8)
       vmware-hgfsmounter(8)
       vmware-user-suid-wrapper(8)
       vmci(9)
       vmhgfs(9)
       vmmemctl(9)
       vmsock(9)
       vmsync(9)
       vmxnet(9)
       vmxnet3(9)

HOMEPAGE

       More information about vmblock and the Open VM Tools can be found at <http://open-vm-tools.sourceforge.net/>.

AUTHOR

       Open VM Tools were written by VMware, Inc. <http://www.vmware.com/>.

       This manual page was put together from homepage materials by Daniel  Baumann  <daniel.baumann@progress-technologies.net>,  for  the  Debian
       project (but may be used by others).

2010.03.20-243334						    2010-04-08								VMBLOCK(9)