02-26-2009
Yes, with topas or nmon for example.
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
Hi,
How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies
2. IP Networking
I have searched this forum for solution and have drawn a blank... so I come to you for help :)
I an a Win XP user that has no problem getting on internet when I am on that OS (currently on it right now ;)). I installed red hat 9 and when I use that OS, I cannot get a connection. I ran the... (10 Replies)
Discussion started by: Minnesota Red
10 Replies
3. UNIX for Dummies Questions & Answers
I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the... (2 Replies)
Discussion started by: Tony Empire
2 Replies
4. AIX
Hi everyone, I recently inherited an IBM RS/6000 43P 150, and it appears that the on board ethernet is dead. Can I put in a PCI ethernet card and use that as the default ethernet connection (as opposed to the one on the motherboard)? If so, what type of card can I use and how does one configure... (2 Replies)
Discussion started by: Jwoollard
2 Replies
5. SCO
Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message:
Fsstat:/dev/boot mounted
Mounted /stand filesystem
System auditing is not enabled.
Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0)
Dlpid:No such... (0 Replies)
Discussion started by: tazmss1
0 Replies
6. IP Networking
What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies
7. UNIX for Dummies Questions & Answers
hai this is nagesh
when i was doing practical , i find some dought.
iam using solaris 9. how can i see the ethernet card speed , wheather it is halfduplex or full duplex.any body please help me (4 Replies)
Discussion started by: nag.mi2000
4 Replies
8. Solaris
I do have a server (SUNV240) with Solaris 9, it has a PCI gigaswift ethernet card for fiber with SC connector, everytime I reboot the server the card won't link up unless I unplug it and plug it back again, for remote operations this is a hassle since sometimes reboots are needed and this card... (3 Replies)
Discussion started by: xe2bss
3 Replies
9. Solaris
Hi,
we have SUN Gigabit ethernet cards at the server, both have 2 lines connected but hiw can I found out which cable is on which port before I configure it: the cards has 4 ports , from right to left the cables are connected at the first right then 2 empty then the last at the left side.
... (1 Reply)
Discussion started by: manni2
1 Replies
10. Solaris
Hi Gurus of Solaris.
I have a problem yesterday when I was installing solaris in a x86 equipement
I attached some log that I capture when I try to resolve the problem
Any guru that can help please.
Any command or procedure that I can run, please advice me
Regards
Andres (10 Replies)
Discussion started by: andresguillen
10 Replies
LEARN ABOUT CENTOS
sigorset
SIGSETOPS(3) Linux Programmer's Manual SIGSETOPS(3)
NAME
sigemptyset, sigfillset, sigaddset, sigdelset, sigismember - POSIX signal set operations.
SYNOPSIS
#include <signal.h>
int sigemptyset(sigset_t *set);
int sigfillset(sigset_t *set);
int sigaddset(sigset_t *set, int signum);
int sigdelset(sigset_t *set, int signum);
int sigismember(const sigset_t *set, int signum);
Feature Test Macro Requirements for glibc (see feature_test_macros(7)):
sigemptyset(), sigfillset(), sigaddset(), sigdelset(), sigismember():
_POSIX_C_SOURCE >= 1 || _XOPEN_SOURCE || _POSIX_SOURCE
DESCRIPTION
These functions allow the manipulation of POSIX signal sets.
sigemptyset() initializes the signal set given by set to empty, with all signals excluded from the set.
sigfillset() initializes set to full, including all signals.
sigaddset() and sigdelset() add and delete respectively signal signum from set.
sigismember() tests whether signum is a member of set.
Objects of type sigset_t must be initialized by a call to either sigemptyset() or sigfillset() before being passed to the functions
sigaddset(), sigdelset() and sigismember() or the additional glibc functions described below (sigisemptyset(), sigandset(), and sig-
orset()). The results are undefined if this is not done.
RETURN VALUE
sigemptyset(), sigfillset(), sigaddset(), and sigdelset() return 0 on success and -1 on error.
sigismember() returns 1 if signum is a member of set, 0 if signum is not a member, and -1 on error. On error, these functions set errno to
indicate the cause.
ERRORS
EINVAL sig is not a valid signal.
CONFORMING TO
POSIX.1-2001.
NOTES
Glibc notes
If the _GNU_SOURCE feature test macro is defined, then <signal.h> exposes three other functions for manipulating signal sets.
int sigisemptyset(sigset_t *set);
returns 1 if set contains no signals, and 0 otherwise.
int sigorset(sigset_t *dest, sigset_t *left, sigset_t *right);
places the union of the sets left and right in dest.
int sigandset(sigset_t *dest, sigset_t *left, sigset_t *right);
places the intersection of the sets left and right in dest.
sigorset() and sigandset() return 0 on success, and -1 on failure.
These functions are nonstandard (a few other systems provide similar functions) and their use should be avoided in portable applications.
SEE ALSO
sigaction(2), sigpending(2), sigprocmask(2), sigsuspend(2)
COLOPHON
This page is part of release 3.53 of the Linux man-pages project. A description of the project, and information about reporting bugs, can
be found at http://www.kernel.org/doc/man-pages/.
Linux 2013-04-19 SIGSETOPS(3)