02-26-2009
Yes, with topas or nmon for example.
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
Hi,
How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies
2. IP Networking
I have searched this forum for solution and have drawn a blank... so I come to you for help :)
I an a Win XP user that has no problem getting on internet when I am on that OS (currently on it right now ;)). I installed red hat 9 and when I use that OS, I cannot get a connection. I ran the... (10 Replies)
Discussion started by: Minnesota Red
10 Replies
3. UNIX for Dummies Questions & Answers
I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the... (2 Replies)
Discussion started by: Tony Empire
2 Replies
4. AIX
Hi everyone, I recently inherited an IBM RS/6000 43P 150, and it appears that the on board ethernet is dead. Can I put in a PCI ethernet card and use that as the default ethernet connection (as opposed to the one on the motherboard)? If so, what type of card can I use and how does one configure... (2 Replies)
Discussion started by: Jwoollard
2 Replies
5. SCO
Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message:
Fsstat:/dev/boot mounted
Mounted /stand filesystem
System auditing is not enabled.
Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0)
Dlpid:No such... (0 Replies)
Discussion started by: tazmss1
0 Replies
6. IP Networking
What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies
7. UNIX for Dummies Questions & Answers
hai this is nagesh
when i was doing practical , i find some dought.
iam using solaris 9. how can i see the ethernet card speed , wheather it is halfduplex or full duplex.any body please help me (4 Replies)
Discussion started by: nag.mi2000
4 Replies
8. Solaris
I do have a server (SUNV240) with Solaris 9, it has a PCI gigaswift ethernet card for fiber with SC connector, everytime I reboot the server the card won't link up unless I unplug it and plug it back again, for remote operations this is a hassle since sometimes reboots are needed and this card... (3 Replies)
Discussion started by: xe2bss
3 Replies
9. Solaris
Hi,
we have SUN Gigabit ethernet cards at the server, both have 2 lines connected but hiw can I found out which cable is on which port before I configure it: the cards has 4 ports , from right to left the cables are connected at the first right then 2 empty then the last at the left side.
... (1 Reply)
Discussion started by: manni2
1 Replies
10. Solaris
Hi Gurus of Solaris.
I have a problem yesterday when I was installing solaris in a x86 equipement
I attached some log that I capture when I try to resolve the problem
Any guru that can help please.
Any command or procedure that I can run, please advice me
Regards
Andres (10 Replies)
Discussion started by: andresguillen
10 Replies
LEARN ABOUT CENTOS
sigsetjmp
SETJMP(3) Linux Programmer's Manual SETJMP(3)
NAME
setjmp, sigsetjmp - save stack context for nonlocal goto
SYNOPSIS
#include <setjmp.h>
int setjmp(jmp_buf env);
int sigsetjmp(sigjmp_buf env, int savesigs);
Feature Test Macro Requirements for glibc (see feature_test_macros(7)):
setjmp(): see NOTES.
sigsetjmp(): _POSIX_C_SOURCE >= 1 || _XOPEN_SOURCE || _POSIX_C_SOURCE
DESCRIPTION
setjmp() and longjmp(3) are useful for dealing with errors and interrupts encountered in a low-level subroutine of a program. setjmp()
saves the stack context/environment in env for later use by longjmp(3). The stack context will be invalidated if the function which called
setjmp() returns.
sigsetjmp() is similar to setjmp(). If, and only if, savesigs is nonzero, the process's current signal mask is saved in env and will be
restored if a siglongjmp(3) is later performed with this env.
RETURN VALUE
setjmp() and sigsetjmp() return 0 if returning directly, and nonzero when returning from longjmp(3) or siglongjmp(3) using the saved con-
text.
CONFORMING TO
C89, C99, and POSIX.1-2001 specify setjmp(). POSIX.1-2001 specifies sigsetjmp().
NOTES
POSIX does not specify whether setjmp() will save the signal mask. In System V it will not. In 4.3BSD it will, and there is a function
_setjmp that will not. By default, Linux/glibc follows the System V behavior, but the BSD behavior is provided if the _BSD_SOURCE feature
test macro is defined and none of _POSIX_SOURCE, _POSIX_C_SOURCE, _XOPEN_SOURCE, _XOPEN_SOURCE_EXTENDED, _GNU_SOURCE, or _SVID_SOURCE is
defined.
If you want to portably save and restore signal masks, use sigsetjmp() and siglongjmp(3).
setjmp() and sigsetjmp() make programs hard to understand and maintain. If possible an alternative should be used.
SEE ALSO
longjmp(3), siglongjmp(3)
COLOPHON
This page is part of release 3.53 of the Linux man-pages project. A description of the project, and information about reporting bugs, can
be found at http://www.kernel.org/doc/man-pages/.
2009-06-26 SETJMP(3)