Multihomed can not ping gateway Post: 302288829

10 More Discussions You Might Find Interesting

1. IP Networking

Unable to ping the gateway IP itself

We are unable to bring one of our linux boxes into the network once it was restarted. But once we stop and start the network service. We are able to ping the gateway and get into network. After a minute or two we get the following reponse for the ping command 64 bytes from 124.168.215.40:...

2. Solaris

ping -s to default gateway very slow

I was install new solaris10 on m4000 model after that i "ping -s" to default gateway but it's take longtime (2 Min) to reply and if i use "ping" only it's reply to fase(2 sec). any body who can tell me about my problem and how to fix it please. i'm try to fix several days.

3. AIX

Can not Ping Gateway

Hello, I am new to Unix :D and have been trying to configure an AIX server running 5.3. I used smitty or smit to configure interface 0 on the server. I am able to ping the IP I set, however I am still unable to ping the gateway. I configured the IP by navigating to Communications Applications...

4. Red Hat

Cannot ping gateway

I know the subject line is very similar to: destination host unreachable but the problem with my machine appears to be somewhat different from that thread. apologies if I missed something from there. We recently moved a machine physically and from one subnet to another . I used...

5. AIX

IBM Server doesn't ping gateway unless you put a static route

Just want to know if someone has a clue about what could be happening here: I have an AIX box with four NICs in Ether channel connected to a Cisco Switch. When I try to ping the default gateway, sometimes it works, but sometimes it doesn't work unless it has a defined static route. Thanks...

6. UNIX for Dummies Questions & Answers

Cannot ping default gateway

I have NCR MP-RAS unix. I have been trying for several months to get our network working since we had never used it before. I have setup all routes that I can think of. I know it has something to do with the routing table, because out of sheer luck I was able to get it working, and than like a...

7. AIX

Cant ping default gateway aix 53 07 new install

I just reinstalled a fresh install of 5300 07 on an old 44p model 170, after installing I set an IP Address on en2 and I tried to the ping default gateway, no response. I tried a startsrc -g tcpip ... and then I can ping the default gateway. I broke the ping and tried again to ping. I cannot...

8. Red Hat

Can not ping default gateway

Hi, Here is the issue: There are 2 identical systems in the same subnet here. They can ping and ssh each other. One can ping the default gateway and one can not with error '... icmp_seq Destination Host Unreachable'. I can't find any difference between the two systems in terms of network...

9. AIX

Networking Issue (Cant Ping the gateway)

Hi, I installed AIX 7.1 on a blade though (hmc with vio). I can ping the IP address, but not the gateway. Is there anything that I should configure? Is there anything that I have to check with vio setting or Am I missing any configuration? Please let me know further. Thank you

10. UNIX for Advanced & Expert Users

Unable to ping default gateway

I have setup a Linux machine on my server but for some reason Im unable to reach my default gateway. This is causing me to not communicate with the outside world (unable to connect to CentOS repos) # ifconfig enp0s3: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet...

LEARN ABOUT NETBSD

bt3c

BT3C(4) 						   BSD Kernel Interfaces Manual 						   BT3C(4)

NAME

     bt3c -- 3Com Bluetooth PC Card driver

SYNOPSIS

     bt3c* at pcmcia? function ?

DESCRIPTION

     The bt3c driver provides support for the 3Com Bluetooth PC Card, model 3CRWB6096, to the Bluetooth protocol stack.

FIRMWARE

     This card needs firmware loaded before it will work. Due to copyright restrictions we cannot distribute the firmware with NetBSD, but if you
     have the card then you should have received a CD with the drivers on, or you may download the latest version from the 3Com website. Create a
     directory named bt3c in the search path of the firmload(9) kernel subsystem. Now, extract the driver archive and find the firmware file
     called BT3CPCC.bin, and place this file in the newly created directory. The firmware will be loaded automatically as needed.

DIAGNOSTICS

     bt3c%d: Cannot open firmware
	  This will be printed to the console if the device cannot open the firmware file as described above.

     bt3c%d: Antenna In
     bt3c%d: Antenna Out
	  If the kernel is compiled with the DIAGNOSTIC option, these messages will be produced on the console when the card antenna position is
	  changed.

     bt3c%d: sleeping
     bt3c%d: waking up
	  These messages will be produced when the card is enabled or disabled due to power change events.

SEE ALSO

     bluetooth(4), pcmcia(4), firmload(9)

HISTORY

     This bt3c device driver was written by Iain Hibbert using FreeBSD and BlueZ drivers as a reference.  It first appeared in NetBSD 4.0.

BUGS

BSD
								 January 14, 2006							       BSD

10 More Discussions You Might Find Interesting

1. IP Networking

Unable to ping the gateway IP itself

Discussion started by: chrisanto_2000

2. Solaris

ping -s to default gateway very slow

Discussion started by: cesmk

3. AIX

Can not Ping Gateway

Discussion started by: cdub50

4. Red Hat

Cannot ping gateway

Discussion started by: mirage