02-17-2009
That's actually a good question. I have to find out. Does that make a difference or? can you monitor both or each separately?
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hello,
Does any one knows any tools or method to monitor users all activities on Solaris 8, including command and its result. Similar to 'script' ???
Thanks
nana (3 Replies)
Discussion started by: nana
3 Replies
2. UNIX for Advanced & Expert Users
Is there a tool or cmd line program i can use to test my tape throughput in Mb/sec?
thank you (2 Replies)
Discussion started by: progressdll
2 Replies
3. IP Networking
As a rule of thumb in doing calculations, what figure would you use in Mbytes/sec? I know the answer varies grealty on the topolgy of the network but I wonde what newteok engineers use a rough rule of thumb?
Many thanks. (1 Reply)
Discussion started by: debd
1 Replies
4. Solaris
Hey guys
First post... and im not exactly a solaris guru but here goes
Ive setup a solaris 10 box with a raidz2 set of 6 disks...
I have also setup Samba with open shares for some CIFs access...
now my issue is that when i transfer large files to it the network performance contantly... (8 Replies)
Discussion started by: silicoon
8 Replies
5. AIX
Dear experts ,
Pls advice for any good Tool to monitor the CPU and performance of AIX the system ..
to keep monitoring to show me the utilization of that system .. (12 Replies)
Discussion started by: Mr.AIX
12 Replies
6. IP Networking
I have a 10Gbps network link connecting two machines A and B. I want to transfer 20GB data from A to B using TCP. With default setting, I can use 50% bandwidth. How to improve the throughput? Is there any way to make throughput as close to 10Gbps as possible? thanks~ :) (3 Replies)
Discussion started by: andrewust
3 Replies
7. Solaris
Hello gurus,
I have the following configuration in the server side:
# dladm show-aggr
key: 33 (0x0021) policy: L4 address: 0:14:4f:6c:11:8 (auto)
device address speed duplex link state
nxge0 0:14:4f:6c:11:8 1000 Mbps ... (3 Replies)
Discussion started by: FERCA
3 Replies
8. IP Networking
Hello,
First time poster here hoping to get some help with ns2.
I've recently started using ns2(first time user) but I'm having difficulty getting the results I'm after.
I am trying to set up a network with wireless nodes(5-15 nodes) and then use xgraph to display a timing diagram,... (0 Replies)
Discussion started by: UnicksMan
0 Replies
9. IP Networking
Hey Guys,
Does anybody know, which OID's of Net-SNMP is used to collect throughput and bandwith usage of machine??
I got these OID's
..iso.org.dod.internet.mgmt.mib-2.interfaces.ifTable.ifEntry.ifOutOctets
..1.3.6.1.2.1.2.2.1.16
... (1 Reply)
Discussion started by: franzramadhan
1 Replies
10. IP Networking
We are using cyberoam device, VPN IPSEC tunnel is going of frequently even the traffic is throug.
Please suggest what may be the cause for the above mentioned issue.
Also suggest a best tool to monitor the same VPN IPSEC tunnel connectivity. (4 Replies)
Discussion started by: marunmeera
4 Replies
iptos(4) Kernel Interfaces Manual iptos(4)
NAME
iptos - Defines the IP Type Of Service (TOS) for FTP and Telnet
SYNOPSIS
/etc/iptos
DESCRIPTION
The /etc/iptos file configures the Type Of Service (TOS) of the Internet Protocol (IP) used by FTP and Telnet.
The TOS field in the Internet datagram is to specify how the datagram should be handled. It is a mechanism to allow control information to
have precedence over data.
Generally, protocols that are involved in direct interaction with a human should select low delay, while data transfers that involve large
blocks of data need high throughput. Finally, high reliability is most important for datagram-based Internet management functions.
In the Tru64 UNIX operating system, the ftp and telnet applications and the ftpd and telnetd daemons allow the configuring of TOS values.
These applications check to see if the /etc/iptos file exists; if the file exists, the applications obtain the TOS value from the file and
use that value to set the TOS field. If the /etc/iptos file does not exist, the applications default to the following TOS values recom-
mended by RFC1060: Low delay High throughput Low delay
Users who want to configure their own TOS values for the TOS field should provide the /etc/iptos file.
Note
Most IP routers do not differentiate based on TOS, and therefore providing values other than the default would have no affect. You
should not change the default values for FTP and Telnet.
Each entry should consist of a single line of the form:
Application Proto TOS-bits aliases
The entry fields contain the following information: The name of an application TOS entry. The protocol name for which the entry is appro-
priate. The TOS value to be set for the entry. A list of aliases that exist for the entry.
Items on an entry line are separated by any number of blanks, tabs, or combination of blanks and tabs. A number sign (#) indicates that
the rest of the line is a comment and is not interpreted by routines that search the file. Blank lines in the file are ignored.
Valid TOS entry names are ftp-control and ftp-data for FTP and telnet for Telnet.
The TOS value for the entry should be one of the following hexadecimal numbers, corresponding to TOS bits: Low delay High throughput High
reliability
If you need to disable the use of TOS bits, because you are having troubling communicating with a TCP/IP host that doe not conform entirely
with the IP specification, you can disable the TOS bits by using the the following settings in the /etc/iptos file:
# # Format of this file: # Application Proto TOS-bits aliases #
ftp-control tcp 0x0 ftp-data tcp 0x0 telnet tcp 0x0
EXAMPLES
The following example shows typical entries in the /etc/iptos file:
# # Format of this file: # Application Proto TOS-bits aliases #
ftp-control tcp 0x10 ftp-data tcp 0x08 telnet tcp 0x10
RELATED INFORMATION
RFC1060, ftp(1), telnet(1), ftpd(8), telnetd(8) delim off
iptos(4)