Sponsored Content
Full Discussion: Reg. Ethernet port
Operating Systems Solaris Reg. Ethernet port Post 302288276 by incredible on Tuesday 17th of February 2009 01:16:06 AM
Old 02-17-2009
You will need to plumb the IP address using ifconfig.
edit the /etc/hosts ,/etc/hostname.<interface>, /etc/netmask, /etc/defaultrouter
 

8 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

determining ethernet port speed in solaris

i purchased, what was labeled as a 4-port fast ethernet sbus card from ebay. i installed it in my ultra1, and it seems to be working fine. how can i determine if the card is infact a fast ethernet card vs. the standard ethernet 4-port card? (7 Replies)
Discussion started by: xyyz
7 Replies

2. Solaris

Ethernet Port Name

I have a new Sun 440 and I am trying to configure it. Non of the Ethernet ports are enabled; when I issue "ifconfig -a" it returns nothing. Is there a way to know the available port name (e.g. ce, bge, etc.) by running a command or so ? (4 Replies)
Discussion started by: StarSol
4 Replies

3. Solaris

Reg- eth0,eth1 (ethernet card)

Hi Guys, I am working as a L-1 support and i want to know that are the precaution need to take on eth0(Ethernet card) i heard on production server it is very much important, what are the steps need to observe on this tickets. (1 Reply)
Discussion started by: kurva
1 Replies

4. AIX

A problem with an unused ethernet port reporting as down...

Good morning, Saw this on a system this morning, thought I'd check with this group before calling IBM. Basically what we have here is a P7 running 6.1 reporting the following in errpt: LABEL: GOENT_LINK_DOWN IDENTIFIER: EC0BCCD4 This is for ent4, which is odd because we... (0 Replies)
Discussion started by: Michael Mullig
0 Replies

5. AIX

vio server ethernet to vio client ethernet(concepts confusing)

Hi In the vio server when I do # lsattr -El hdisk*, I get a PVID. The same PVID is also seen when I put the lspv command on the vio client partition. This way Im able to confirm the lun using the PVID. Similarly how does the vio client partition gets the virtual ethernet scsi client adapter... (1 Reply)
Discussion started by: newtoaixos
1 Replies

6. Shell Programming and Scripting

command to match ethernet port to network card

hi I juts want to know if there is a command that checks if an ethernet port corresponds to a network card. ex. I have 3 network cards, one is two ports, and the other two 8 ports. How do I know that eth0 corresponds to the the two-port network card and eth9 corresponds to the first 8-port... (2 Replies)
Discussion started by: h0ujun
2 Replies

7. Red Hat

Ethernet Port device path?

Hi, I have a server program that reads data coming in on USB ports. Device paths are in the format: /dev/ttyUSB0 Now, I would like to log data from another device coming in over Ethernet. My first step is trying to track down what the correct device path is which I am unsure of. Anyone... (9 Replies)
Discussion started by: fedora18
9 Replies

8. Solaris

How to find port number wwn of particular port on dual port HBA,?

please find the below o/p for your reference bash-3.00# fcinfo hba-port HBA Port WWN: 21000024ff295a34 OS Device Name: /dev/cfg/c2 Manufacturer: QLogic Corp. Model: 375-3356-02 Firmware Version: 05.03.02 FCode/BIOS Version: BIOS: 2.02; fcode: 2.01;... (3 Replies)
Discussion started by: sb200
3 Replies
defaultrouter(4)						   File Formats 						  defaultrouter(4)

NAME
defaultrouter - configuration file for default router(s) SYNOPSIS
/etc/defaultrouter DESCRIPTION
The /etc/defaultrouter file specifies a IPv4 host's default router(s). The format of the file is as follows: IP_address ... The /etc/defaultrouter file can contain the IP addresses or hostnames of one or more default routers, with each entry on its own line. If you use hostnames, each hostname must also be listed in the local /etc/hosts file, because no name services are running at the time that defaultrouter is read. Lines beginning with the ``#'' character are treated as comments. The default routes listed in this file replace those added by the kernel during diskless booting. An empty /etc/defaultrouter file will cause the default route added by the kernel to be deleted. Use of a default route, whether received from a DHCP server or from /etc/defaultrouter, prevents a machine from acting as an IPv4 router. You can use routeadm(1M) to override this behavior. FILES
/etc/defaultrouter Configuration file containing the hostnames or IP addresses of one or more default routers. SEE ALSO
in.rdisc(1M), in.routed(1M), routeadm(1M), hosts(4) SunOS 5.10 17 Aug 2004 defaultrouter(4)
All times are GMT -4. The time now is 06:15 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy