02-12-2009
Is this affecting all jumpstart clients or just this one server? If it's just this 1 client please tell me what model server you're using.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I have been asked to research Jumpstart and don't know where to begin! Any ideas would be much appreciated! Thanks! :-) (1 Reply)
Discussion started by: avana100
1 Replies
2. UNIX for Dummies Questions & Answers
Hi,
Which sites have general information on JumpStart for Solaris 8?
I would like to know more about boot server, installation server, and configuration server.... and all other good things about JumpStart....Thanks..:p
Doo... (2 Replies)
Discussion started by: dookeobih
2 Replies
3. UNIX for Advanced & Expert Users
HI.
i was wondering if you can jumpstart using the solaris intel platform? please help thanks (3 Replies)
Discussion started by: souldier
3 Replies
4. UNIX for Advanced & Expert Users
Hi,
where can i find documention on how to create a jumpstart system?
dori (2 Replies)
Discussion started by: dorilevy
2 Replies
5. Solaris
Hello all,
I configured a jumpstart server ( the server is in the same subnet as the client) and gave boot net - install in the client.
The client boots up shows the banner and then displays error:
cant read disk label
cant open disk label package
and then goes to OK prompt.
What... (1 Reply)
Discussion started by: Pratik Gharti
1 Replies
6. Solaris
Hi Peeps,
Created a jumpstart server for an unattened install and it works, but got 2 bugs in the config which I would like to work out:
when you boot net install
It still asks you to select a language and locale, after you do this it kicks of an unattended install.
So my question is,... (5 Replies)
Discussion started by: callmebob
5 Replies
7. Solaris
I'm trying to jumpstart my remote server. My /etc/hosts and /etc/ethers files have the correct data. Keep getting the following message at the ok prompt
after running a boot net - install
Link hasn't comeup yet
Ran a test-net and got the following message.
Link is -- down
When... (7 Replies)
Discussion started by: soupbone38
7 Replies
8. Solaris
hi friends,
i dont know how to install jumpstart . i have solaris cds( 5 nos.). i tried to install jumpstart but there is no setup_install_server file. What i want to do for installing jumpstart server
please help me
thanks to all (8 Replies)
Discussion started by: sijocg
8 Replies
9. Solaris
1.I wish to perform a Jumpstart installation, the client being Ultra 5 Sparc
and jumpstart Server being ultra 20 AMD system.
2.I think i have done all the procedures right, like putting the mac address of Sparc 1 to /etc/ethers, creating sysidcfg file, and profile file:
3.When I issued the boot... (7 Replies)
Discussion started by: saagar
7 Replies
10. Solaris
I'm trying to use a V210 (sun4u) configured as a jumpstart server to flash install a number of T5220's (sunv4).
The Facts:
V210 - Solaris 10 (September 2010 Release / not patched)
T5220's - Archive's created using prior (unknown) version of solaris 10.
Flar -i <archive name> shows the... (6 Replies)
Discussion started by: Celtic_Monkey
6 Replies
statd(1M) statd(1M)
NAME
statd, rpc.statd - network status monitor
SYNOPSIS
DESCRIPTION
is an RPC server. It interacts with to provide the crash and recovery functions for the locking services on NFS (see lockd(1M)).
keeps track of the clients with processes which hold locks on a server. When the server reboots after a crash, sends a message to the on
each client indicating that the server has rebooted. The client processes then informs the on the client that the server has rebooted.
The client then attempts to reclaim the lock(s) from the server.
on the client host also informs the on the server(s) holding locks for the client when the client has rebooted. In this case, the on the
server informs its that all locks held by the rebooting client should be released, allowing other processes to lock those files.
Options
recognizes the following options and command-line arguments:
This is an obsolete option. All messages and errors are logged to
WARNINGS
The crash of a server is only detected upon its recovery.
FILES
lists hosts and network addresses to be contacted after a reboot
lists hosts and network addresses that could not be contacted after last reboot
includes a number which changes during a reboot
AUTHOR
was developed by Sun Microsystems, Inc.
SEE ALSO
lockd(1M), fcntl(2), lockf(2), signal(2), sm(4).
statd(1M)