Sponsored Content
Full Discussion: Processor and processor core
Operating Systems AIX Processor and processor core Post 302286930 by balaji_prk on Thursday 12th of February 2009 10:57:34 AM
Old 02-12-2009
Java Processor and processor core

Guys...

Hows it going???

I have been going through the hardware spec of IBM system p systems.. and here i am confused

for IBM Power 520 Express it says

Processor cores:

One, two or four 64-bit 4.2 GHz POWER6 with AltiVec™ SIMD and Hardware Decimal Floating-Point acceleration

now my question is

- is 1/2/4 the number of processors that 520 can have each of 4.2 GHz?

or

- is 1/2/4 the number of cores per processor giving effective 4,2GHz speed. in that case, how many processors can 520 have to the maximum?

Regret if am not clear.. ready to explain if required
 

8 More Discussions You Might Find Interesting

1. Shell Programming and Scripting

How to get Processor Id

Hi Everyone I am new to unix. I ahve few quries that i would like to post. Is there any way by which i get the unique processor Id. Actually i am unable to find any logic and method to get access to Processor Id. Is it possible to get it. I read it on Intel site that the new processor do no... (1 Reply)
Discussion started by: atul.saxena
1 Replies

2. AIX

LPAR processor/virtual processor settings

Question is on setting of Physical and Virtual processors for LPARs to make proper use of virtualization capabilities. Environment is a 8-way p570 with 4 LPARs. lparVIO1 and lparVIO2: AIX 5300-04-01 Mode/Type= Shared-SMT/Capped Minimum Processors= 0.10 Desired Processors= 0.50 Maximum... (1 Reply)
Discussion started by: guttew
1 Replies

3. Linux

linux for dual core processor

hi all I bought a new MSI motherboard and intel dual core processor . i have currently installed fedora core 3 for which audio is not detected . can u tell me which version of fedora core will support as i have tried with fedora core 6 which gets installed but gives a error while... (0 Replies)
Discussion started by: nageshrk
0 Replies

4. Red Hat

finding no of core in processor

Hi, what is command to find out no of core per procssor? Regards, Manoj (4 Replies)
Discussion started by: manoj.solaris
4 Replies

5. Linux Benchmarks

AMD Phenom(tm) 9950 Quad-Core Processor, Ram: 3.6 GB, Foxconn 7da-s and Linux 2.6.26-2-amd64

CPU/Speed: AMD Phenom(tm) 9950 Quad-Core Processor Ram: 3.6 GB Motherboard: Foxconn 7da-s Bus: Cache: Controller: Disk: Load: Kernel: Linux 2.6.26-2-amd64 Kernel ELF?: pgms: ============================================================== BYTE UNIX Benchmarks (Version... (0 Replies)
Discussion started by: migracho
0 Replies

6. HP-UX

how can i know this processor quad or dual core ?

hi every body i want to know if i have server with hp-ux os if i did "machinfo" i will see no of cpu = for example 16 how can i know this is dual or quad core . thanks (2 Replies)
Discussion started by: maxim42
2 Replies

7. Shell Programming and Scripting

m4 processor (how to use)

hi, what plugins i need to install to run m4 processor in bash shell. Also, what is the file extension for m4 processor ( like .cc in c ). Thanks (1 Reply)
Discussion started by: Learnerabc
1 Replies

8. UNIX for Dummies Questions & Answers

Help for processor

hello Admins, how to find number of processor in unix machine. (2 Replies)
Discussion started by: vipinkumarr89
2 Replies
psrinfo(1)						      General Commands Manual							psrinfo(1)

NAME
psrinfo, pinfo - Displays processor administration information SYNOPSIS
/usr/sbin/psrinfo -n /usr/sbin/psrinfo [-v] [processor...] /usr/sbin/psrinfo -s processor /usr/sbin/pinfo [-v] [processor...] OPTIONS
Displays the number of processors in the system. Enables verbose mode. Writes only a boolean value to standard output. The -s option requires a single processor identification number (processor). The -s option is intended to be used in scripts. A value of 1 is output if the specified processor is on line. A value of 0 is output if the specified processor is off line. DESCRIPTION
The psrinfo and pinfo commands display information about processors. The processor variable specifies the processor identification number, which is a unique integer that identifies the processor. If you do not specify any options or a processor identification number, the com- mands display information about all processors. EXAMPLES
The following is an example of the default prsinfo command output (no options or processor identification numbers): greene:> psrinfo 0 on-line since 11/03/1999 09:41:34 1 on-line since 11/03/1999 09:41:34 2 off-line since 11/03/1999 08:41:34 The following example shows how to use the psrinfo command with the -s option in a shell script to determine the state of the pro- cessor with an identification number of 1: if [ "`psrinfo -s 1 2> /dev/null`" -eq 1 ] then echo "processor 1 is up" else echo "processor 1 is down" fi The following example shows how to use the psrinfo command with the -v option: % psrinfo -v Status of processor 0 as of: 05/23/00 15:47:40 Processor has been on-line since 05/23/2000 15:08:04 The alpha EV5.6 (21164A) processor operates at 465 MHz, and has an alpha internal floating point processor. Status of processor 1 as of: 05/23/00 15:47:40 Processor has been on-line since 05/23/2000 15:08:04 The alpha EV5.6 (21164A) processor operates at 465 MHz, and has an alpha internal floating point processor. Status of processor 2 as of: 05/23/00 15:47:40 Processor has been off-line since 05/23/2000 15:08:04 The alpha EV5.6 (21164A) processor operates at 465 MHz, and has an alpha internal floating point processor. Status of processor 3 as of: 05/23/00 15:47:40 Processor has been on-line since 05/23/2000 15:14:00 The alpha EV5.6 (21164A) processor operates at 465 MHz, and has an alpha internal floating point processor. FILES
SEE ALSO
Commands: pset_assign_cpu(1), pset_assign_pid(1), pset_info(1), psradm(8) Files: utmp(4) Processor Sets: processor_sets(4) psrinfo(1)
All times are GMT -4. The time now is 11:55 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy