02-09-2009
That command would restore everything on the tape.
You can gain more control by first doing a listing using:
restore -t
then explicity naming the files you want to recover with
restore -x
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi all,
I am attempting to read tar images from a DLT tape, and have recieved an error, which i don't know:
tar: blocksize = 8
tar: directory checksum error
I have been able to read from other tapes, using the same command (tar -tvf /devicename) but this time i have an... (3 Replies)
Discussion started by: colesy
3 Replies
2. UNIX for Dummies Questions & Answers
I have been attempting to read a DLT tape, but encountered problems. I have applied patches from SUN that 'resolve' known problems with tape reading etc...but still the error!
Techsupport reckon that the data/tape is corrupt. I would like to think they aren't.
Are there any issues with... (10 Replies)
Discussion started by: colesy
10 Replies
3. AIX
I am experimenting with one of my TSM processes, and I am trying to write something to a 4mm tape.
I tried to use the tctl command, but, I was unsuccessful.
what AiX command can I run in order to see if my output is on the tape ?
Thank You ! (0 Replies)
Discussion started by: DATDANGGADUDE
0 Replies
4. AIX
I'm attempting to read a tape in a 4mm drive (AIX 4.3) using the following command...
tar tvf /dev/rmt0
...and I keep getting the following error message:
tar: 0511-193 An error occurred while reading from the media.
There is not enough memory available now.
I've googled this error... (2 Replies)
Discussion started by: tdpearson
2 Replies
5. UNIX for Advanced & Expert Users
I've got a backuptape in cpio format that was accidentally overwritten with a very small batch file. As I assume that the cpio header has been overwritten, I cannot extract files from the backup in the conventional manner:
( cpio -itv </dev/rct0
cpio: this is not a cpio file, bad header)
... (0 Replies)
Discussion started by: mart4179
0 Replies
6. SCO
when I do a tape status /dev/rStp0 I get the following on a new tape and I have tried several:
Status : ready beginning-of-tape
soft errors : 0
hard errors: 2
underruns: 5
My BackupEdge has stopped backing up my system because it asks for a new volume yet my total system data is under 20... (5 Replies)
Discussion started by: psytropic
5 Replies
7. UNIX for Dummies Questions & Answers
Does anyone know how to read an LTO tape from this jukebox? (3 Replies)
Discussion started by: dr. phreeze
3 Replies
8. AIX
Hi, how can I find out though kron shell (aix 4.2) what the label of a tape is ?
Also, how can I find out if that tape has been used for an mksysb and when ? (1 Reply)
Discussion started by: Browser_ice
1 Replies
9. Red Hat
Thanks for any insights you might have...
I have a RH8 system setup with a DAT drive.
I have a AIX tape that was made using cpio.
Bottom line is I need to read the AIX tape into the RH box.
I was able to do cpio -itv --no-absolute-filenames < /dev/st0 and read the table of contents.
... (0 Replies)
Discussion started by: mike114327
0 Replies
10. Solaris
Hello,
I'm brand new to Sun/Solaris.
I have a Sun Blade 150, with SunOS 5.8.
I wanted to make a backup to prevent future data loss, so I put the disk in a normal PC with Windows XP to try to make a backup with Norton Ghost, the disk was detected, but not the file volume, so I place the disk... (6 Replies)
Discussion started by: Resadija
6 Replies
RESTOR(1M) RESTOR(1M)
NAME
restor - incremental file system restore
SYNOPSIS
restor key [ argument ... ]
DESCRIPTION
Restor is used to read magtapes dumped with the dump command. The key specifies what is to be done. Key is one of the characters rRxt
optionally combined with f.
f Use the first argument as the name of the tape instead of the default.
r or R The tape is read and loaded into the file system specified in argument. This should not be done lightly (see below). If the key is
R restor asks which tape of a multi volume set to start on. This allows restor to be interrupted and then restarted (an icheck -s
must be done before restart).
x Each file on the tape named by an argument is extracted. The file name has all `mount' prefixes removed; for example, /usr/bin/lpr
is named /bin/lpr on the tape. The file extracted is placed in a file with a numeric name supplied by restor (actually the inode
number). In order to keep the amount of tape read to a minimum, the following procedure is recommended:
Mount volume 1 of the set of dump tapes.
Type the restor command.
Restor will announce whether or not it found the files, give the number it will name the file, and rewind the tape.
It then asks you to `mount the desired tape volume'. Type the number of the volume you choose. On a multivolume dump the recom-
mended procedure is to mount the last through the first volume in that order. Restor checks to see if any of the files requested
are on the mounted tape (or a later tape, thus the reverse order) and doesn't read through the tape if no files are. If you are
working with a single volume dump or the number of files being restored is large, respond to the query with `1' and restor will read
the tapes in sequential order.
If you have a hierarchy to restore you can use dumpdir(1) to produce the list of names and a shell script to move the resulting
files to their homes.
t Print the date the tape was written and the date the filesystem was dumped from.
The r option should only be used to restore a complete dump tape onto a clear file system or to restore an incremental dump tape onto this.
Thus
/etc/mkfs /dev/rp0 40600
restor r /dev/rp0
is a typical sequence to restore a complete dump. Another restor can be done to get an incremental dump in on top of this.
A dump followed by a mkfs and a restor is used to change the size of a file system.
FILES
default tape unit varies with installation
rst*
SEE ALSO
dump(1), mkfs(1), dumpdir(1)
DIAGNOSTICS
There are various diagnostics involved with reading the tape and writing the disk. There are also diagnostics if the i-list or the free
list of the file system is not large enough to hold the dump.
If the dump extends over more than one tape, it may ask you to change tapes. Reply with a new-line when the next tape has been mounted.
BUGS
There is redundant information on the tape that could be used in case of tape reading problems. Unfortunately, restor doesn't use it.
RESTOR(1M)