02-09-2009
logged in as root run lpstat -t. that will give you a listing of printers and their hardware location plus status. You may have to pipe the output through more if there is a bunch of stuff waiting for the printer.
If you have a bunch of stuff waiting to print you can cancel it by job number.
You may want to tail -40 /usr/adm/messages | more to see the last boot up report to see if the serial ports you are using are active.
If you are on a different serial port now the port speed may be an issue.
Serial printer wiring sometimes gets messy. Helps to have the telltale and forcing the signal levels is easier if you have a 232 patch kit. This is a small board, 25p on one side, 25s on the other with all lines from both sides brought out to pluggable jacks so you can jumper what you need.
Starting point on a 25 patch kit is 2, 3, and 7 going across, 4&5 shorted on both sides, and 6&20 shorted on both sides. The 4,5,6, &20 are normally connected across as flow controls but forcing them is no problem if the printer is faster than the serial port.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I've just installed Unix SCO OpenServer System v in an Intel PC and Everithing ok, except just one thing, in the begining of the installation the wizard asked me about the mouse , i have a generic 3 buttons mouse and i took a logitech and did not work
i need to change the mouse configuration, ... (2 Replies)
Discussion started by: jimmyvaldes
2 Replies
2. UNIX for Dummies Questions & Answers
hello!
when i try to make my system dual boot with both win98 & sco open server 5.5 it doesn't work at all.neither win98 take start nor sco open server boots.what should i do ?
kindly help me
thanks (1 Reply)
Discussion started by: buntty
1 Replies
3. UNIX for Advanced & Expert Users
I am doing some work for a customer that is running SCO 5.0.2 openserver and they have lost their cd. Is there anyplace I can download it? I have a replacement being shipped but it will not be here for two days and they are down. Any ideals? (3 Replies)
Discussion started by: SCOoT
3 Replies
4. UNIX for Dummies Questions & Answers
I connected a serial printer to my scoOpenServer which works great. I was able to disable the banner in the interface of the printer. However i am unable to find the command in the interface to disable the formfeed . Below is a copy of the interface file. Please can anyone instruct me on how to... (0 Replies)
Discussion started by: scoman2
0 Replies
5. UNIX for Dummies Questions & Answers
Hello,
I have searched the web for a couple hours now and have found no results, and I cam across the site and thought, "Why not?"
In the office that I work, we run an old SCO OpenServer 5.5 box. We are just about to open a branch that needs to connect to that server, but we do not know how... (3 Replies)
Discussion started by: czimmerman
3 Replies
6. UNIX for Dummies Questions & Answers
i have wipro netpower server with p4 and 256 ram.
i want share dot matrix printer installed on windows 2000 prof.
with sco openserver 5.0.5. plz help me to comeout from this trouble. (0 Replies)
Discussion started by: raj_shivage
0 Replies
7. UNIX for Dummies Questions & Answers
Hi there guys.
I just got this new SCO version and i'm having some problem printing from shell,
This is what i'm typing at the # sign : lp -dHP /etc/hosts and it prints no problem but when i use any other user at the $ sign it gives me this error.
/dev/fd/7: /usr/lib/lp/sysv/7: not found.
... (1 Reply)
Discussion started by: josramon
1 Replies
8. UNIX for Dummies Questions & Answers
Hi guys,
I just got this new 6.0 version and i'm trying to setup a remote office to telnet to this server running sco 6.0, in previous version all i have to do is add this file under /etc/rc2.d call S99route and put the gate in that file and that was it, for some reason in 6.0 it does not... (1 Reply)
Discussion started by: josramon
1 Replies
9. SCO
Dear members
when i installed dual processor patch in openserver 5.0.7 in hp ML370 G4 server it hangs in sco at G_hd_config.
i tried MP4, EFS 5.64,5.70A but not solved the problem.. (0 Replies)
Discussion started by: M_farooqui
0 Replies
10. SCO
I need SCO Openserver 4.2. Please, give me distributive of that version SCO:eek: (0 Replies)
Discussion started by: caine
0 Replies
ports(7) Miscellaneous Information Manual ports(7)
NAME
ports, port_names - Device (tty and lp) names for serial and parallel ports
SYNOPSIS
Default Serial Ports:
/dev/tty00
/dev/tty01 (not present on a single-port system)
Parallel Port:
/dev/lp0
DESCRIPTION
AlphaStation and AlphaServer systems provide one or two 9-pin serial communication ports. These ports are usually labelled 1 (COMM1) and 2
(COMM2), but they may be identified by different icons. Using the appropriate serial cable and terminator, you can connect a serial
printer, external modem, or character-cell terminal to a serial port. Most AlphaStation and AlphaServer systems also provide one parallel
port, for use with a parallel printer.
When you add a device to your system, the installation documentation may instruct you to map the device pathname to the port. These
devices are located in the /dev directory.
For serial-line ports, the two default device pathnames are: This pathname always maps to 1, COMM1, the lowest port number, an icon for a
terminal console, or the only serial port (on a single-port system). This pathname always maps to 2, COMM2, the next numbered port, or (if
one serial port is labeled with an icon for a terminal console) the remaining serial port.
If your system hardware has been extended to include additional serial ports, the pathnames /dev/tty02, /dev/tty03, and so forth, may also
be available to you. However, most systems have only /dev/tty00 and /dev/tty01 as the device pathnames for serial ports.
The one parallel port on an AlphaStation or AlphaServer may be labeled with the word printer or a printer icon. On some systems, the paral-
lel port may not be labeled. The device pathname for the parallel port is /dev/lp0. Currently, Tru64 UNIX does not fully support parallel
printers, so fewer devices are connected to this port as compared to serial ports.
If you are connecting a terminal console to your system, it must be connected to the serial port mapped to /dev/tty00. For other serial
devices, it does not matter which of the serial ports you choose for the connection. For example, suppose you are setting up a system that
has two serial ports, labeled 1 and 2. You intend to use a serial-line terminal rather than a workstation monitor as the system console and
also want to connect a serial-line printer to the system. In this case, you must connect the terminal to the port labeled 1 (with the
device pathname /dev/tty00). Therefore, you must connect the printer to the remaining port labeled 2 (with the device pathname /dev/tty01).
If, for the same type of system, you intend to use a workstation monitor as the system console, it does not matter which serial port you
use for a serial-line printer or modem. In other words, you can connect the printer to either port 1 (with pathname /dev/tty00) or port 2
(with pathname /dev/tty01). When prompted to enter a /dev/tty** pathname by the lprsetup script or the Print configuration tool in the CDE
Application Manager, you would specify /dev/tty00 if you connected the printer to port 1 or /dev/tty01 if you connected the printer to port
2.
See the System Administration manual for more information on setting up consoles (including remote consoles) and printers. See the
modem(7) reference page for more information on setting up modems.
SEE ALSO
Commands: lprsetup(8)
Devices: ace(7), modem(7)
System Administration delim off
ports(7)