Login or Register to Ask a Question and Join Our Community

Sponsored Content
Full Discussion: Network not working on Solaris 10
Operating Systems Solaris Network not working on Solaris 10 Post 302285498 by dn100 on Monday 9th of February 2009 04:39:22 AM
Old 02-09-2009
# ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000
iprb0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2 inet 172.16.1.12 netmask ffffff00 broadcast 172.16.1.255 ether 0:1e:90:cd:9a:a4


 

10 More Discussions You Might Find Interesting

1. IP Networking

home network not working!

i just linked 2 100MHz Linux kernel 2.4.2 boxes togeather using a direct cable connection, on two 3Com PCI network cards, using the EtherLink III chipset. Unfortuanately, when I boot both PCs, i get a loading interface: eth0 for five minutes, then a failed flag. No networking suppt. in windows,... (2 Replies)
Discussion started by: boris888
2 Replies

2. Solaris

Getting solaris on my network

I have a solaris x86 box that ive been having trouble getting on my network, anyone know a good guide that can take me through it step by step? (1 Reply)
Discussion started by: xtremepancakez
1 Replies

3. Solaris

rare network problem even-- reinstall is not working

i am not able to install solaris 10 i have installed solaris many times succesfully with wotking network after that abrupt power failure i was never able to start solaris and neither install during install it hangs IS IT PROBABLE THAT BIOS OR SOME OTHER SETTINGS RELATED TO HARDWARE IS... (3 Replies)
Discussion started by: simaich8
3 Replies

4. Solaris

solaris 8 network

hi all, how do i change the routing info and make sure i will be able to connect remotely? any ideas please? thanks in advance. (5 Replies)
Discussion started by: itik
5 Replies

5. Solaris

Executable compiled on solaris 10 not working on solaris 9

Hi I compiled an executable on Solaris 10 which creates semaphore ( semget) but it didn't work on solaris 9 , while it is executing sucessfully on solaris 10. It is throwing the system error that Invalid arguments ( system error 22) on solaris 9. the ldd for the executable on two servers is as... (4 Replies)
Discussion started by: ash_bit2k2
4 Replies

6. Ubuntu

Wireless network not working

Hi, I am a new to Ubuntu linux and trying to learn it. I am using ubuntu 10.04. I am getting problem in setting my wireless network. I set it up properly and was working fine. But suddenly it stopped working, though the wireless icon saying that it is connected, but can't load any page. I... (2 Replies)
Discussion started by: linux_learner
2 Replies

7. SCO

Printing to a working network printer using PCL

I am trying to get a network printer to work that currently works from my Unix (5.0.7) server when printing text files only. When I try to print post script files like a PDF file I get all of the controls so I am not sure if I have my printer configuration setup properly in Unix The printer... (1 Reply)
Discussion started by: ziggy6
1 Replies

8. Solaris

Network of Virtual machine not working

Hello, I have a problem. I have a server SPARC T3-1 with solaris 11 on the base. The server is working well. And then i did a virtual machine using again Solaris 11 to do this, but now my notwork on my virtual machine is not working anymore. There says that the network that i have created is... (11 Replies)
Discussion started by: keziacp
11 Replies

9. Red Hat

Network Teaming not working in RHEL/CentOS 7

I was testing Networking Teaming (activebackup) with a VM hosted on VmWare Workstation and VirtualBox, and the result is, if the active interface is down, the system is not using the backup interface. Tested on both CentOS / RHEL 7 Please find below the command I have used to configure teaming.... (0 Replies)
Discussion started by: atanubanerji
0 Replies

10. UNIX for Beginners Questions & Answers

Solaris 11 LDOM guest network not working

I'm really stuck here. I've created an LDOM on a SPARC T4-1 with Solaris 11.4 to run a copy of Linux for SPARC. I got the Linux ISO installed and Linux itself installed and booted OK. The only thing is is that there's no networking available in the Linux guest. This question is basically the... (7 Replies)
Discussion started by: Michele31416
7 Replies

LEARN ABOUT MINIX

ifconfig

IFCONFIG(8)						      System Manager's Manual						       IFCONFIG(8)

NAME

       ifconfig - configure a TCP/IP device

SYNOPSIS

       ifconfig [-I ip-device] [-h ipaddr] [-n netmask] [-iv]

DESCRIPTION

       Ifconfig  initializes a TCP/IP device setting the IP address and/or netmask.  It will report the address and netmask set.  This command may
       be used if the system has not been configured properly yet.  It is only used at boot time to set a fixed address for  a	system	without  a
       physical ethernet.  Normally the inet task will find it out by itself from the RARP server.

OPTIONS

       -h     The decimal TCP/IP address to set.

       -n     The netmask to set.

       -i     Don't set the IP address or netmask if already set.  This way ifconfig cannot interfere if the numbers have been found out by RARP.

       -v     Report IP address and netmask.  This is the default action if there are no other options.

SEE ALSO

       hostaddr(1), rarpd(8), set_net_default(8), boot(8).

AUTHOR

       Kees J. Bot (kjb@cs.vu.nl)

																       IFCONFIG(8)
All times are GMT -4. The time now is 06:51 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy