|
|
Sponsored Content
Special Forums
IP Networking
Multihomed can not ping gateway
Post 302285313 by Neo on Sunday 8th of February 2009 12:28:50 PM
|
|
10 More Discussions You Might Find Interesting
1. IP Networking
We are unable to bring one of our linux boxes into the network once it was restarted. But once we stop and start the network service. We are able to ping the gateway and get into network. After a minute or two we get the following reponse for the ping command
64 bytes from 124.168.215.40:... (6 Replies)
Discussion started by: chrisanto_2000
6 Replies
2. Solaris
I was install new solaris10 on m4000 model after that i "ping -s" to default gateway but it's take longtime (2 Min) to reply and if i use "ping" only it's reply to fase(2 sec). any body who can tell me about my problem and how to fix it please. i'm try to fix several days. (2 Replies)
Discussion started by: cesmk
2 Replies
3. AIX
Hello,
I am new to Unix :D and have been trying to configure an AIX server running 5.3. I used smitty or smit to configure interface 0 on the server. I am able to ping the IP I set, however I am still unable to ping the gateway. I configured the IP by navigating to Communications Applications... (6 Replies)
Discussion started by: cdub50
6 Replies
4. Red Hat
I know the subject line is very similar to: destination host unreachable
but the problem with my machine appears to be somewhat different from that thread. apologies if I missed something from there.
We recently moved a machine physically and from one subnet to another . I used... (1 Reply)
Discussion started by: mirage
1 Replies
5. AIX
Just want to know if someone has a clue about what could be happening here:
I have an AIX box with four NICs in Ether channel connected to a Cisco Switch.
When I try to ping the default gateway, sometimes it works, but sometimes it doesn't work unless it has a defined static route.
Thanks... (1 Reply)
Discussion started by: witt
1 Replies
6. UNIX for Dummies Questions & Answers
I have NCR MP-RAS unix. I have been trying for several months to get our network working since we had never used it before. I have setup all routes that I can think of. I know it has something to do with the routing table, because out of sheer luck I was able to get it working, and than like a... (4 Replies)
Discussion started by: Rutgerncas
4 Replies
7. AIX
I just reinstalled a fresh install of 5300 07 on an old 44p model 170, after installing I set an IP Address on en2 and I tried to the ping default gateway, no response. I tried a
startsrc -g tcpip
... and then I can ping the default gateway. I broke the ping and tried again to ping. I cannot... (1 Reply)
Discussion started by: asyed123
1 Replies
8. Red Hat
Hi,
Here is the issue: There are 2 identical systems in the same subnet here. They can ping and ssh each other. One can ping the default gateway and one can not with error '... icmp_seq Destination Host Unreachable'. I can't find any difference between the two systems in terms of network... (4 Replies)
Discussion started by: aixlover
4 Replies
9. AIX
Hi,
I installed AIX 7.1 on a blade though (hmc with vio). I can ping the IP address, but not the gateway. Is there anything that I should configure?
Is there anything that I have to check with vio setting or Am I missing any configuration?
Please let me know further.
Thank you (5 Replies)
Discussion started by: pjeedu2247
5 Replies
10. UNIX for Advanced & Expert Users
I have setup a Linux machine on my server but for some reason Im unable to reach my default gateway. This is causing me to not communicate with the outside world (unable to connect to CentOS repos)
# ifconfig
enp0s3: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet... (3 Replies)
Discussion started by: Junaid Subhani
3 Replies
LEARN ABOUT SUSE
laptop_mode
LAPTOP_MODE(8) System Manager's Manual LAPTOP_MODE(8) NAME
/usr/sbin/laptop_mode - apply laptop mode settings SYNOPSIS
/usr/sbin/laptop_mode [ cmd ] [ force ] DESCRIPTION
This manual page documents briefly the /usr/sbin/laptop_mode command. laptop_mode is a program that applies the settings given in the /etc/laptop-mode/laptop-mode.conf configuration file. The primary use is to control the laptop mode feature included in Linux kernels with versions 2.6.6 and higher, and 2.4.23 and higher. This feature increases battery life by letting your hard drive spin down. This is achieved by grouping disk write activity into "chunks" that are spaced at larger intervals than they normally would be. In addition to sup- porting the Linux kernel's laptop mode feature, /usr/sbin/laptop_mode also supports various power saving modules which are configured through configuration files in the /etc/laptop-mode/conf.d directory. It is not recommended to call /usr/sbin/laptop_mode directly to start or stop laptop mode, except in hardware event handlers. To apply new configuration settings from laptop-mode.conf, call the laptop-mode service init script with the reload parameter. COMMANDS
Specify force as the second parameter to force laptop_mode to re-apply a state even if the computer is already in that state. These are the values that are allowed for cmd : auto Enable or disable laptop mode based on the current power state. Note that this will not do anything if the laptop-mode service has not been started! status Display a status report about everything that laptop_mode affects. SEE ALSO
laptop-mode.conf(8). AUTHOR
This manual page was written by Bart Samwel (bart@samwel.tk) for the Debian system (but may be used by others). Permission is granted to copy, distribute and/or modify this document under the terms of the GNU General Public License, Version 2 any later version published by the Free Software Foundation. On Debian systems, the complete text of the GNU General Public License can be found in /usr/share/common-licenses/GPL. LAPTOP_MODE(8)