02-07-2009
10 More Discussions You Might Find Interesting
1. AIX
Hi all
I need command to give logical and physical IP Address for my machine.
thank you (1 Reply)
Discussion started by: magasem
1 Replies
2. AIX
I added a static route through smit using:
Communications applications and Services ==>
TCIP/IP ==>
Further Configuration ==>
Static Routes ==>
Add a Static Route ==>
Route Type of host
Filled in Destination Address, Default Gateway Address and Network Interface of en0.
This... (2 Replies)
Discussion started by: jyoung
2 Replies
3. UNIX for Dummies Questions & Answers
Hi there,
I have a Debian 5.0 server newly installed.
By default, the ip address is given by dhcp.
pegase:~# grep '^' /etc/network/interfaces
auto lo
iface lo inet loopback
allow-hotplug eth0
iface eth0 inet dhcp
pegase:~# head -2 /etc/hosts
127.0.0.1 localhost
127.0.1.1 ... (1 Reply)
Discussion started by: chebarbudo
1 Replies
4. Solaris
Hello friend, I am new in UNIX, but I want to learn a lot
Well I have a problem to try to configure my PC with a static IP Address
(IP 192.168.1.39, Mask 255.255.255.0, gateway 192.168.1.1)
(DNS 200.48.225.130 and 200.48.225.146).
where are the file that I must be change?
The SO is Sun Solaris... (15 Replies)
Discussion started by: andresguillen
15 Replies
5. UNIX for Dummies Questions & Answers
Hi guys,
I got one problem which I definetily no idea.
What would the physical address be for virtual address?
1) 2ABC
2) 3F4B
Here is the page table:see attached
Thank you sos sososososso much!! (0 Replies)
Discussion started by: lemon_06
0 Replies
6. Red Hat
Hi All,
Could you please explain the purpose of assigning the static IP by using the DHCP Concept. Like by using the clients MAC address we assign the static IP Address. Waiting for your reply. Thanks in Advance. (6 Replies)
Discussion started by: Sharath Kumar
6 Replies
7. SCO
Hi,
Just a question of thought. Why one needs to add static routes on Unix servers ? If I had ethernet card, it already has the settings for gateway for incoming and outgoing requests. We donot have to explicitly set the route it should take. Then what is the use... (3 Replies)
Discussion started by: dextergenious
3 Replies
8. Red Hat
Hi All,
Is there a quick way to check whether the current routes on my centos are
persistent or not before rebooting ?
i can take a route -n output but i may completely lost access to my server if the routes are gone.
thanks. (1 Reply)
Discussion started by: coolatt
1 Replies
9. IP Networking
Hi all,
I would need to register a random free subdomain address and associate that to my IP Address. Any suggestion of a good service?
Also I don't have a static IP but i remember that there are services that automatically reset the right IP address behind the subdomain but i don't remember... (1 Reply)
Discussion started by: Tameto
1 Replies
10. Red Hat
I have three systems A,B,C. I want to configure A in such a way that all packets from A to C goes via B.
I tried:
1. ip route add 'ip of C' via 'ip of B'
2. route add -net 'net address' netmask gw 'ip of B'
These commands work initially when I try a ping or traceroute and expire after... (2 Replies)
Discussion started by: kanak
2 Replies
LEARN ABOUT FREEBSD
nos-tun
NOS-TUN(8) BSD System Manager's Manual NOS-TUN(8)
NAME
nos-tun -- implement ``nos'' or ``ka9q'' style IP over IP tunnel
SYNOPSIS
nos-tun -t tunnel -s source -d destination -p protocol_number [source] target
DESCRIPTION
The nos-tun utility is used to establish an nos style tunnel, (also known as ka9q or IP-IP tunnel) using a tun(4) kernel interface.
Tunnel is the name of the tunnel device /dev/tun0 for example.
Source and destination are the addresses used on the tunnel device. If you configure the tunnel against a cisco router, use a netmask of
``255.255.255.252'' on the cisco. This is because the tunnel is a point-to-point interface in the FreeBSD end, a concept cisco does not
really implement.
Protocol number sets tunnel mode. Original KA9Q NOS uses 94 but many people use 4 on the worldwide backbone of ampr.org.
Target is the address of the remote tunnel device, this must match the source address set on the remote end.
EXAMPLES
This end, a FreeBSD box on address 192.168.59.34:
nos-tun -t /dev/tun0 -s 192.168.61.1 -d 192.168.61.2 192.168.56.45
Remote cisco on address 192.168.56.45:
interface tunnel 0
ip address 192.168.61.2 255.255.255.252
tunnel mode nos
tunnel destination 192.168.59.34
tunnel source 192.168.56.45
AUTHORS
Nickolay N. Dudorov <nnd@itfs.nsk.su> wrote the program, Poul-Henning Kamp <phk@FreeBSD.org> wrote the man-page. Isao SEKI
<iseki@gongon.com> added a new flag, IP protocol number.
BUGS
We do not allow for setting our source address for multihomed machines.
BSD
April 11, 1998 BSD