02-06-2009
Hi,
tnx, but how do you know which one is for interface e1000g1 and which one for e1000g2?
mehrdad
10 More Discussions You Might Find Interesting
1. AIX
Hi all
I need command to give logical and physical IP Address for my machine.
thank you (1 Reply)
Discussion started by: magasem
1 Replies
2. AIX
I added a static route through smit using:
Communications applications and Services ==>
TCIP/IP ==>
Further Configuration ==>
Static Routes ==>
Add a Static Route ==>
Route Type of host
Filled in Destination Address, Default Gateway Address and Network Interface of en0.
This... (2 Replies)
Discussion started by: jyoung
2 Replies
3. UNIX for Dummies Questions & Answers
Hi there,
I have a Debian 5.0 server newly installed.
By default, the ip address is given by dhcp.
pegase:~# grep '^' /etc/network/interfaces
auto lo
iface lo inet loopback
allow-hotplug eth0
iface eth0 inet dhcp
pegase:~# head -2 /etc/hosts
127.0.0.1 localhost
127.0.1.1 ... (1 Reply)
Discussion started by: chebarbudo
1 Replies
4. Solaris
Hello friend, I am new in UNIX, but I want to learn a lot
Well I have a problem to try to configure my PC with a static IP Address
(IP 192.168.1.39, Mask 255.255.255.0, gateway 192.168.1.1)
(DNS 200.48.225.130 and 200.48.225.146).
where are the file that I must be change?
The SO is Sun Solaris... (15 Replies)
Discussion started by: andresguillen
15 Replies
5. UNIX for Dummies Questions & Answers
Hi guys,
I got one problem which I definetily no idea.
What would the physical address be for virtual address?
1) 2ABC
2) 3F4B
Here is the page table:see attached
Thank you sos sososososso much!! (0 Replies)
Discussion started by: lemon_06
0 Replies
6. Red Hat
Hi All,
Could you please explain the purpose of assigning the static IP by using the DHCP Concept. Like by using the clients MAC address we assign the static IP Address. Waiting for your reply. Thanks in Advance. (6 Replies)
Discussion started by: Sharath Kumar
6 Replies
7. SCO
Hi,
Just a question of thought. Why one needs to add static routes on Unix servers ? If I had ethernet card, it already has the settings for gateway for incoming and outgoing requests. We donot have to explicitly set the route it should take. Then what is the use... (3 Replies)
Discussion started by: dextergenious
3 Replies
8. Red Hat
Hi All,
Is there a quick way to check whether the current routes on my centos are
persistent or not before rebooting ?
i can take a route -n output but i may completely lost access to my server if the routes are gone.
thanks. (1 Reply)
Discussion started by: coolatt
1 Replies
9. IP Networking
Hi all,
I would need to register a random free subdomain address and associate that to my IP Address. Any suggestion of a good service?
Also I don't have a static IP but i remember that there are services that automatically reset the right IP address behind the subdomain but i don't remember... (1 Reply)
Discussion started by: Tameto
1 Replies
10. Red Hat
I have three systems A,B,C. I want to configure A in such a way that all packets from A to C goes via B.
I tried:
1. ip route add 'ip of C' via 'ip of B'
2. route add -net 'net address' netmask gw 'ip of B'
These commands work initially when I try a ping or traceroute and expire after... (2 Replies)
Discussion started by: kanak
2 Replies
LEARN ABOUT X11R4
ip-token
IP-TOKEN(8) Linux IP-TOKEN(8)
NAME
ip-token - tokenized interface identifier support
SYNOPSIS
ip token { COMMAND | help }
ip token set TOKEN dev DEV
ip token del dev DEV
ip token get [ dev DEV ]
ip token [ list ]
DESCRIPTION
IPv6 tokenized interface identifier support is used for assigning well-known host-part addresses to nodes whilst still obtaining a global
network prefix from Router advertisements. The primary target for tokenized identifiers are server platforms where addresses are usually
manually configured, rather than using DHCPv6 or SLAAC. By using tokenized identifiers, hosts can still determine their network prefix by
use of SLAAC, but more readily be automatically renumbered should their network prefix change [1]. Tokenized IPv6 Identifiers are described
in the draft [1]: <draft-chown-6man-tokenised-ipv6-identifiers-02>.
ip token set - set an interface token
set the interface token to the kernel.
TOKEN the interface identifier token address.
dev DEV
the networking interface.
ip token del - delete an interface token
delete the interface token from the kernel.
dev DEV
the networking interface.
ip token get - get the interface token from the kernel
show a tokenized interface identifier of a particular networking device. Arguments: coincide with the arguments of ip token set but the
TOKEN must be left out.
ip token list - list all interface tokens
list all tokenized interface identifiers for the networking interfaces from the kernel.
SEE ALSO
ip(8)
AUTHOR
Manpage by Daniel Borkmann
iproute2 28 Mar 2013 IP-TOKEN(8)