smc2582w-b bridge and solaris 10 wireless network Post: 302282865

9 More Discussions You Might Find Interesting

1. Cybersecurity

Wireless Network

At the moment, I have three computers at home. I want to use boardband for my three computers. But I don't want to use network at home. I have been looking for a product which call OriNoCo USB Cilent. How do I connect to the internet with my computer?? If I post this in a wrong place, please...

2. IP Networking

Wireless-G network

Hi, I have a laptop with a Linksys Wireless G PCMCIA card and a cable connection goin into a router and then a patch lead from the router going to a Linksys Wireless G access point IP 192.168.1.245 with DHCP disabled. I can connect to the access point from the laptop, but how do I get the...

3. UNIX for Dummies Questions & Answers

solaris 10 wireless network setup

I installed solaris 10 x86 on my dell laptop on a partition alongside windows xp. I am able to connect to the internet in xp with both my ethernet local area connection as well as through my wireless network card. But, however i do not have clue as to how to go about it in solaris. i did not...

4. Ubuntu

Wireless network not working

Hi, I am a new to Ubuntu linux and trying to learn it. I am using ubuntu 10.04. I am getting problem in setting my wireless network. I set it up properly and was working fine. But suddenly it stopped working, though the wireless icon saying that it is connected, but can't load any page. I...

5. Ubuntu

Wireless Bridge/Repeater ?

I have a laptop running Ubuntu Netbook Remix. What I want to do is use it to connect to my routers wifi, and then plug my desktop into the laptops ethernet port and be hooked to my routers network without any NAT or ICS. Desktop>>>>>>Laptop/Wired>>Laptop/Wireless>>>>>Router I want it to look...

6. Red Hat

[SOLVED] Wireless Network Setup

Hi, I am trying to set up a wireless internet connection on my centos OS (6). I can connect via the copper using the internal LAN but cannot get the wireless connection working. The 2 files that I have configured are: My wpa_supplicant.conf: ctrl_interface=/var/run/wpa_supplicant...

7. Android

Problem with wireless network

Good day, everybody! I have a mobile phone (LG Optimus L5) with Android 4.0.3 and a tablet (PocketBook SurfPad 2) with Android 4.1.1 and I have problem with wireless network on these devices. Laptops don't have such problem. My wireless network organisation is a modem connected with an access point...

8. Ubuntu

Could not connect to wireless network

I run lubuntu from usb (try lubuntu, it's not install on my pc ) And i try to connect to network I see the network name And i put the pass But it's not connect.. I tried to open hot spot on my phone and try to connect and it's not connect I have edumax n150 Try to install new driver -...

9. Linux

Is possible to bridge wlan0 and eth0 using network manager?How to for wpa?

I have created a bridge with nmcli between eth0 and wlan0 I use this procedure sudo nmcli con add ifname br0 type bridge con-name br0 sudo nmcli con add type bridge-slave ifname eth0 master br0 sudo nmcli con add type bridge-slave ifname wlan0 master br0 sudo nmcli con modify br0...

LEARN ABOUT MINIX

liebert

LIEBERT(8)							    NUT Manual								LIEBERT(8)

NAME

       liebert - Driver for Liebert contact-closure UPS equipment

NOTE

       This man page only documents the hardware-specific features of the liebert driver. For information about the core driver, see nutupsdrv(8).

SUPPORTED HARDWARE

       This driver supports some Liebert UPS equipment with a contact-closure interface. This includes the UPStation GXT2 with their
       contact-closure cable. The smart mode ("Multilink") cable is not supported by this driver.

EXTRA ARGUMENTS

       This driver does not support any extra settings in the ups.conf(5).

BUGS

       This driver does not yet support shutdowns by raising DTR. Be aware that shutdowns are not possible with the stock contact-closure cable.
       You may have to build another cable with DTR connected through to the UPS for it to work.

       There is no way for this driver to detect the hardware or cable. It will start up successfully even if no UPS is present. This is a
       fundamental limitation of any contact-closure driver.

SEE ALSO

   The core driver:
       nutupsdrv(8)

   Internet resources:
       The NUT (Network UPS Tools) home page: http://www.networkupstools.org/

Network UPS Tools						    05/21/2012								LIEBERT(8)