setup network interface Post: 302281599

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Network Interface

Hi ! Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !! Thx in adivance ! Witt

2. IP Networking

I am moving a SUN 250 server from one location to another. The IP address has to change in order to make the server visible in the new building. The system administrator has given me the new IP address for the server, the DNS server IP and the default gateway IP. First question, is this all the...

3. IP Networking

network setup???

Hello everybody, I am a new unix user (Solaris 10). I was wondering if anybody can help me figure out how to connect to the network in my work place. I know my IP address, subnet mask, gateway, primary and secondary DNS addresses but I don't know how to enter these settings into my Solaris. ...

4. Solaris

configure zones to have different network interface and network

i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ? Thanks

5. UNIX and Linux Applications

Access to network interface (Mac-network)

Hi, I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan. For that I must access to network interface to develope my personal stack based on standard 802.15.4. Can you help me? I need an explanation for that.

6. IP Networking

Network interface-

Hello, Please what's the difference between: AND Thank you so much

7. IP Networking

network interface -

Hello, Please, how can i create a network interface with a routable IP address on linux (ubuntu) ? AND How can i desactivate an interface? Thank you so much for help.

8. Solaris

No network cable But Network interface is UP and Running

I've one Netra 240 After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces. I tried to restart and plumb/unplumb with no luck. ifconfig -a...

9. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without...

10. IP Networking

Can't setup new interface.

Hi all, Currently I am running Solaris 10 update 10 machine. My current ifconfig -a output is: ifconfig -a lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 bge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu...

LEARN ABOUT XFREE86

inet_type

inet_type(4)							   File Formats 						      inet_type(4)

NAME

       inet_type - default Internet protocol type

SYNOPSIS

       /etc/default/inet_type

DESCRIPTION

       The inet_type file defines the default IP protocol to use. Currently this file is only used by the ifconfig(1M) and netstat(1M) commands.

       The  inet_type  file  can  contain  a  number of <variable>=<value> lines. Currently, the only variable defined is DEFAULT_IP, which can be
       assigned a value of IP_VERSION4, IP_VERSION6, or BOTH.

       The output displayed by the ifconfig and netstat commands can be controlled by the value of DEFAULT_IP set in inet_type file.  By  default,
       both commands display the IPv4 and IPv6 information available on the system. The user can choose to suppress display of IPv6 information by
       setting the value of DEFAULT_IP.  The following shows the possible values for DEFAULT_IP and the resulting ifconfig and netstat output that
       will be displayed:

       IP_VERSION4     Displays only IPv4 related information. The output displayed is backward compatible with older versions of the ifconfig(1M)
		       and netstat(1M) commands.

       IP_VERSION6     Displays both IPv4 and IPv6 related information for ifconfig and netstat.

       BOTH	       Displays both IPv4 and IPv6 related information for ifconfig and netstat.

       The command-line options to the ifconfig and netstat commands override the effect of DEFAULT_IP as set in the inet_type file. For  example,
       even if the value of DEFAULT_IP is IP_VERSION4, the command

       example% ifconfig -a6

       will display all IPv6 interfaces.

EXAMPLES

       Example 1: Suppressing IPv6 Related Output

       This is what the inet_type file must contain if you want to suppress IPv6 related output:

       DEFAULT_IP=IP_VERSION4

SEE ALSO

       ifconfig(1M), netstat(1M)

SunOS 5.10							    16 Jun 1999 						      inet_type(4)

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Network Interface

Discussion started by: witt

2. IP Networking

Network Setup

Discussion started by: pkappaz