|
|
Sponsored Content
Operating Systems
Solaris
6120 Array. Additional physical Disks and ZFS
Post 302281132 by DukeNuke2 on Wednesday 28th of January 2009 09:30:21 AM
01-28-2009
|
|
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
We have 6 hard disks attached to the hardware. Of this 2 hard disks are of 9 GB each.
Now I want combine both the same in such a way that i see a combined entry in the output of df -k .
The steps I follow are
1. Create partition on hard disks (Using format partition)
2. Run newfs -v for... (6 Replies)
Discussion started by: Hitesh Shah
6 Replies
2. UNIX for Dummies Questions & Answers
Hello,
I would like to know if there are commands that can be used to monitor the state of physical disks (including RAID) under AIX and SUN unix platforms?
Thank you in advance. (4 Replies)
Discussion started by: VeroL
4 Replies
3. UNIX for Dummies Questions & Answers
Can anyone tell me what Vertias is?
Is it free? What is it used for exactly?
Thank you in advance. (1 Reply)
Discussion started by: VeroL
1 Replies
4. Filesystems, Disks and Memory
How do I check for physical damage on red hat linux hard disks? I tried smartctl /dev/sdb but it came back so fast saying it was ok. Is there a better linux command to check for bad sectors or physical disks in linux? Is there a good way such as with parted or something else? I normally in HP... (4 Replies)
Discussion started by: taekwondo
4 Replies
5. AIX
This is the report I got running the comand rptconf, but I would like to know what is the capacity of the disks installed into our server power 6 with AIX
System Model: IBM,7778-23X
Machine Serial Number: 1066D5A
Processor Type: PowerPC_POWER6
Processor Implementation Mode: POWER 6... (6 Replies)
Discussion started by: cucosss
6 Replies
6. Solaris
Hi,
kstat -p -m zfs -n arcstats -s size returns
zfs:0:arcstats:size 8177310584
this values is approx (7.61 GB)
but my Physical Memory size is only 6144 Megabytes.
Can this happen ?
if yes, then how can I find free memory on the system.
BTW, I ran the kstat commands from a Non... (2 Replies)
Discussion started by: sapre_amit
2 Replies
7. Red Hat
I wanted to know how we can combine volumes over 2 physical drives.
# fdisk -l
Disk /dev/sda: 42.9 GB, 42949672960 bytes
255 heads, 63 sectors/track, 5221 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/sda1 ... (16 Replies)
Discussion started by: ikn3
16 Replies
8. Solaris
I'd like to finish setting up this system and then move the secondary or primary disk to another system that is the exact same hardware.
I've done things like this in the past with ufs and disk suite mirroring just fine. But I have yet to do it with a zfs root pool mirror.
Are there any... (1 Reply)
Discussion started by: Metasin
1 Replies
9. Solaris
Hi,
I am on Sun Edge 6120 Disk array. When I do port listmap.
The failover status below means I have to take action. I never used Sun Array before. Please advice.
port targetid addr_type lun volume owner access
u1p1 1 hard 0 v0 ... (0 Replies)
Discussion started by: samnyc
0 Replies
10. Solaris
Generally, this is what we do:-
On primary, export 2 LUNs (add-vdsdev).
On primary, assign these disks to the ldom in question (add-vdisk).
On ldom, created mirrored zpool from these two disks.
On one server (which is older) we have:-
On primary, create mirrored zpool from the two LUNs.... (4 Replies)
Discussion started by: psychocandy
4 Replies
LEARN ABOUT DEBIAN
backup_quit
BACKUP_QUIT(8) AFS Command Reference BACKUP_QUIT(8) NAME
backup_quit - Leaves interactive mode SYNOPSIS
quit [-help] q [-h] DESCRIPTION
The backup quit command exits interactive mode, returning the issuer to the regular shell prompt at which the backup or backup interactive command was issued to enter interactive mode. The command has no effect when issued outside interactive mode. Issuing the Ctrl-D command also exits interactive mode. CAUTIONS
To exit interactive mode, all jobs must be completed. Use the backup jobs command to list any jobs currently pending or executing, and the backup kill command to terminate them as necessary. OPTIONS
-help Prints the online help for this command. All other valid options are ignored. EXAMPLES
The following command exits interactive mode: backup> quit % PRIVILEGE REQUIRED
None SEE ALSO
backup(8), backup_interactive(8), backup_jobs(8), backup_kill(8) COPYRIGHT
IBM Corporation 2000. <http://www.ibm.com/> All Rights Reserved. This documentation is covered by the IBM Public License Version 1.0. It was converted from HTML to POD by software written by Chas Williams and Russ Allbery, based on work by Alf Wachsmann and Elizabeth Cassell. OpenAFS 2012-03-26 BACKUP_QUIT(8)