Sponsored Content
Special Forums IP Networking How to down interface without name Post 302280139 by djbuly on Monday 26th of January 2009 05:31:44 AM
Old 01-26-2009
Quote:
Originally Posted by fpmurphy
What OS and version?
Is Red Hat Enterprise Linux 3 (Taroon)
 

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Network Interface

Hi ! Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !! Thx in adivance ! Witt (4 Replies)
Discussion started by: witt
4 Replies

2. Solaris

interface may off

Dear ALL, my server give me messages like below: Apr 20 21:33:09 TAISERVER in.routed: interface bge3 to 192.168.11.22 turned off I check with ifconfig,but nothing error that,how can make it solve...thanks for your help. (7 Replies)
Discussion started by: fredginting
7 Replies

3. Solaris

no such interface

Hi Community, I've a problem with an interface of my Sun Workstation: when I try to plumb hme0 interface I see this output: # ifconfig hme0 <ip_address> netmask <mask> plumb #ifconfig: plumb: hme0: no such interface I've the same thing with dhcp service. could you provide any solution... (1 Reply)
Discussion started by: Sunb3
1 Replies

4. UNIX for Advanced & Expert Users

interface problem

hi all, i have problem with my box, until now i can't investigate the root cause of my issue at my box. here the problem. i have a box as a squid server just forward all request packet from one interface and receive the packet then forward to client at the same interface. but after 5 hours i... (1 Reply)
Discussion started by: tindasz
1 Replies

5. Solaris

Command line Interface or GUI Interface not shown on solaris

Dear all, I am a newbie in solaris and I need your advice. I have a Solaris version 5.9 installed on Sunfire V240. I am able to ssh the machine from putty remotely. My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies

6. SCO

Change SCO - GUI or Desktop interface to DOS based interface

Hi all I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface? If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies

7. IP Networking

Need a bridge from an ethernet interface to a serial interface

This is my situation DOS pc serial cable (sl0) Linux Pc eth1 192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router) I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface. ... (3 Replies)
Discussion started by: mghis
3 Replies

8. UNIX for Dummies Questions & Answers

Interface

Hi All, How to check whether a Interface has a single port or dual port.Thanks in advance. (5 Replies)
Discussion started by: rama krishna
5 Replies

9. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
RHN_REGISTER(8) 						   Red Hat, Inc.						   RHN_REGISTER(8)

NAME
rhn_register - Connect to Spacewalk Server, Red Hat Satellite or Red Hat Network Classic. SYNOPSIS
rhn_register [options] DESCRIPTION
rhn_register is a client program that registers your system with "Spacewalk Server", "Red Hat Satellite" or "Red Hat Network Classic". After registering, your system can receive software updates, install new software, and remotely manage your system. It can run both in graphical and text modes. OPTIONS
-v, --verbose Increase the debugging output. --proxy=PROXY Specify an http proxy to use. --proxyUser=PROXYUSER Specify a username to use for an authenticated proxy. This option must be used in conjunction with proxyPassword. --proxyPassword=PROXYPASSWORD Specify a password to use for an authenticated proxy. This option must be used in conjunction with proxyUser. --nox Run in text mode. --version Show the program's version number and exit. -h, --help Show a help message and exit. FILES
/etc/sysconfig/rhn/systemid The digital server ID for this machine if the system has been registered onto "Spacewalk Server" or "Red Hat Satellite" or "Red Hat Network Classic". This file does not exist otherwise. /etc/sysconfig/rhn/up2date The common configuration file used by Red Hat client programs. SEE ALSO
rhn_check(8), rhnreg_ks(8), rhnsd(8), rhn-profile-sync(8), rhnplugin(8), up2date(5). AUTHORS
See the AUTHORS file included with this software. This manual page was written by James Bowes <jbowes@redhat.com> BUGS
Report bugs to <http://bugzilla.redhat.com>. COPYRIGHT
Copyright (C) 1999-2011 Red Hat, Inc. This is free software; see the source for copying conditions. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICU- LAR PURPOSE. Linux 2011 February 4 RHN_REGISTER(8)
All times are GMT -4. The time now is 03:36 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy