01-14-2009
You may want to look at the networksetup binary, in /usr/sbin it has many networking options.
9 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
Hello,
I am new to db2 SQL in unix so bear with me while I try to explain the situation. I have a text file that has the contents of the where condition that I am using for a db2 SQL in UNIX ksh.
Here is the snippet.
if ;
then
echo "Begin processing VALUEs"
... (1 Reply)
Discussion started by: jerardfjay
1 Replies
2. IP Networking
I'm running an arp -an on a Solaris 10 box. We're using IPMP. One of the systems is not able to see a host on the same network. The only difference between the two systems (one is having a problem, the other isn't) at least so far is the output of arp:
# arp -an | grep 224.55
e1000g5... (1 Reply)
Discussion started by: BOFH
1 Replies
3. Shell Programming and Scripting
ok, so I have a script im running on a linux box that uses "egrep" a lot. now, when i run this script, i check the TOP to see how much system resource it is using.
the "top" command gives the following output:
last pid: 25384; load avg: 1.06, 1.04, 0.76; up 351+06:30:24 ... (0 Replies)
Discussion started by: SkySmart
0 Replies
4. UNIX for Dummies Questions & Answers
Is it possible for both commands to work? (1 Reply)
Discussion started by: phunkypants
1 Replies
5. UNIX for Dummies Questions & Answers
After running nm command on any object file from out put can we get to know that wheather a symbol is a call to a function or definition of function ?
I am searching a class and function definitions inside many .so files.
I have 3 files which contain the symbol but I don't know wheather they... (2 Replies)
Discussion started by: yatrik007
2 Replies
6. Shell Programming and Scripting
I'm trying to gather information on the interfaces on a large number of servers.
If I run ifconfig I will get: eth0 Link encap:Ethernet HWaddr 00:50:56:A2:27:C1
inet addr:10.145.xxx.xxx Bcast:10.152.45.255 Mask:255.255.254.0
-----
eth1 Link... (2 Replies)
Discussion started by: C0ppert0p
2 Replies
7. UNIX for Dummies Questions & Answers
Hi there,
I need your help in understanding the below Solaris 10 ifconfig output;
athnetspns02>ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
e1000g0:... (2 Replies)
Discussion started by: wthomas
2 Replies
8. Shell Programming and Scripting
Hi There,
I have a Solaris server that has a bunch of zones configured and I am trying to write a script that will take all interfaces other than the loopback ones (e.g. lo0:3 etc) and present them so that I can easily determine the zone that owns the IP
So in the case of the following... (2 Replies)
Discussion started by: hcclnoodles
2 Replies
9. Red Hat
I ran the following command.
cat abc.c > abc.c
I got message the following message from command cat:
cat: abc.c : input file is same as the output file
How the command came to know of the destination file name as the command is sending output to standard file. (3 Replies)
Discussion started by: ravisingh
3 Replies
whereis(1) General Commands Manual whereis(1)
NAME
whereis - Locates files for programs
SYNOPSIS
whereis [-bms] [-u] [-BMS directory... -f] program...
The whereis command locates source, binary, and/or reference page files for the specified program program.
OPTIONS
The -b, -m, and -s options can be used in combination to restrict the search. Searches for an executable program. Searches for the refer-
ence page for a program. Searches for the sources of a program.
Use the -B, -M, and -S options to change or limit the places whereis searches. Specifies the binary directories to search. Specifies the
reference page directories to search. Specifies the source directories to search.
The other options that can be used with whereis are as follows: Terminates the last directory list and signals the start of program names.
Used with other options to indicate when there is no file for program in the default or specified directory or directories (source, binary,
or reference page).
DESCRIPTION
The whereis program locates source, binary, and reference pages for the specified programs. When looking for a match, the program names
are stripped of leading pathname components and any trailing extensions of the form (for example, s. resulting from the use of the Source
Code Control System see sccs(1), are also handled.
The default directories searched by the whereis command are as follows: /etc /etc/nls /sbin /usr/bin /usr/lbin /usr/lbin/spell /usr/ccs/lib
/usr/lib /usr/local /usr/hosts /usr/sbin
EXAMPLES
To find files matching cat in the default source, binary, and reference directories, enter: whereis cat To search for reference pages for
app13 in the directory /usr/local/man, enter: whereis -M /usr/local/man -f -f appl3 To find the programs in /usr/bin that do not have ref-
erence pages in /usr/share/man/man1 with source files in /usr/src/cmd, enter: whereis -u -M /usr/share/man/man1
-S /usr/src/cmd -f /usr/bin/* To find which files in the current directory either have no reference pages in the default reference
directories or have more than one, enter: whereis -m -u *
FILES
Default binary directories. Default binary directories. Default reference directories. Default source directories.
SEE ALSO
Commands: apropos(1), find(1), man(1), which(1), catman(8)
whereis(1)